Ok, getting very close. I am picking up a Helix 12 GN2 Mega SI to do all my sounding. I want to add a high speed 2D ducer. I have an AS SI DB Y, but think I need instead is a 9M SI DB-Y (part # 720101-1) Am I correct?
Ches.
Ok, getting very close. I am picking up a Helix 12 GN2 Mega SI to do all my sounding. I want to add a high speed 2D ducer. I have an AS SI DB Y, but think I need instead is a 9M SI DB-Y (part # 720101-1) Am I correct?
Ches.
2013 Lund 2010 Pro Guide, 150 Verado SN:2B024387
2X Helix 12's Mega G2N's, Lvl. 2 Merc Monitor
That is correct.
Wes
Helix 10 MSI+,MDI+,Ultrex IPilot
2023 Phoenix 818
Never assume there's a tomorrow
2013 Lund 2010 Pro Guide, 150 Verado SN:2B024387
2X Helix 12's Mega G2N's, Lvl. 2 Merc Monitor
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Thanks again guys. It's all the little details that I struggle with. Somewhere I read it had one more pin, but didn't know why.
Ches.
2013 Lund 2010 Pro Guide, 150 Verado SN:2B024387
2X Helix 12's Mega G2N's, Lvl. 2 Merc Monitor
What cable(s) would I need to link 10 inch g2n mega si helix at the console to a 10 inch g2n mega di helix at the bow? Just going with transom mount si transducer on console unit and trolling motor mount on bow. Haven’t ordered yet and wanted to know what I needed above what comes with the units. Thanks.
2015 Bullet 21XRS, 2021 250 Pro XS 4s - 3B014359
Each unit needs an Ethernet adapter to connect an Ethernet cable to them---AS EC QDE.
Then you need an Ethernet cable to go between them---AS EC 20E is the 20' version.
The bow DI unit comes with a transom transducer and you should use a trolling motor puck instead. Exchange via Customer Service for the XTM 9 MDI T.
https://www.humminbird.com/Products/XTM-9-MDI-T/
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Thanks
2015 Bullet 21XRS, 2021 250 Pro XS 4s - 3B014359
Hello Sirs;
Could I see Side imaging from dash unit on a DI unit at Trolling Motor (both G2N) through networking ?
I've readed a lot of post but still get doubting about it...
Many thanks in advance.
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Many thanks Wayne !!!
Here in Spain people says that you can't see with you DI unit side imaging from SI unit just because DI unit doesn't have this tecnology so can't support it...
Do you know if there are some video on the net just for show them...
Many thanks in advance again...
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Thank you so much Wayne P.
I don't have a video of it, but I've seen me do it on my last boat.
Current boat has a Helix 10 SI Mega and a Helix 10 GPS on the console, and a Gelix 10 GPS on the bow. There is not a single doubt in my mind that I will be able to see the imaging from the rear transducer on all three graphs across the network. If I thought for a minute that I wouldn't be able to do it, I would have purchased different units.
Tell your friends to sign up for an account here and we'll set them straight.
Or, you can order a pair of Helix units and show them. :)
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
I have an ultrex and want to mount a mega chirp g2n Si transducer on the trolling motor.
Are there any adapter plates for this?
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
I have a Solix 12 and an Onix 10 CIT (no transducer currently connected to the Onix) at my console, and a Solix 15 and Ultrex Ipilot on my bow, all networked through an Ethernet switch. . I want to install a shoot through transducer so I can have depth while on plane. Which is the better method/option?
A) Use the 14 MSIDB "Y" adapter with a XP 14 20 or XP 14 20T shoot through transducer, hooked up through the Solix 12? or......
B) Install the XP 14 20 or XP 14 20T transducer and connect direct to Onix 10 CIT
I already have the 14 MSIDY "Y" cable, and a XP 14 20 transducer.
I had a similar set up on my Z18 with (2) Helix 10 G2N's on the console. I used the "Y" cable and connected it to the Helix Mega G2N. Worked well, but these Solix's are a whole different animal. Not sure what works best.
'17 Nitro Z21, 250ProXS serial # 2B399616, 24p Fury4, 12" Atlas, Apex 16 @ console, Apex 16 & Apex 13 @ bow, Mega 360, Ultrex, 8ft blades
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
'17 Nitro Z21, 250ProXS serial # 2B399616, 24p Fury4, 12" Atlas, Apex 16 @ console, Apex 16 & Apex 13 @ bow, Mega 360, Ultrex, 8ft blades