Results 1 to 13 of 13
  1. 09-06-2021, 01:49 PM #1
    tracer1
    tracer1 is offline
    tracer1 tracer1's Avatar
    Join Date
    Jun 2013
    Location
    Aiken, SC
    Posts
    2,393

    Power Pole Pumps

    Can anyone decipher this label (sticker) located on the bottom of the blade power pole?
    Which is the newer of the two pumps and are they compatible?
    When the one of the left is powered up, only get one red light will flash, the nothing.
    The other one will show a flashing green light.
    Any help would be appreciated.
    Thanks

    IMG_1453.jpg IMG_1454.jpg
    Reply With Quote Reply With Quote
  2. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    10,937
    #2 09-06-2021, 04:23 PM
    newer one is on the right, they are compatible yes one on left older cm 1.0 othe newer cm 1.0 is on right flashing green is what you want. flashing red.... check inline fuse holder for corrosion make sure battery leads are good check to see getting 12 volts at the cap check wiring where goes into the cap. all that checks out need a circuit board.


    Reply With Quote Reply With Quote
  3. tracer1
    tracer1 is offline
    tracer1 tracer1's Avatar
    Join Date
    Jun 2013
    Location
    Aiken, SC
    Posts
    2,393
    #3 09-06-2021, 06:29 PM
    Thank you sir, appreciate that. Could you make anything out of the s/n, assuming that's what it is.
    Reply With Quote Reply With Quote
  4. tracer1
    tracer1 is offline
    tracer1 tracer1's Avatar
    Join Date
    Jun 2013
    Location
    Aiken, SC
    Posts
    2,393
    #4 09-06-2021, 07:07 PM
    K&K, how can I tell what gen PP these are. 8 ft blades, signature series.
    Thanks
    Reply With Quote Reply With Quote
  5. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    10,937
    #5 09-07-2021, 09:17 AM
    give power pole a call w the serial #s


    Reply With Quote Reply With Quote
  6. tracer1
    tracer1 is offline
    tracer1 tracer1's Avatar
    Join Date
    Jun 2013
    Location
    Aiken, SC
    Posts
    2,393
    #6 09-08-2021, 06:32 PM
    Did that, talked to Scott.
    Reply With Quote Reply With Quote
  7. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    10,937
    #7 09-08-2021, 07:24 PM
    Quote Originally Posted by tracer1 View Post
    Did that, talked to Scott.
    Scott is the man...


    Reply With Quote Reply With Quote
  8. tracer1
    tracer1 is offline
    tracer1 tracer1's Avatar
    Join Date
    Jun 2013
    Location
    Aiken, SC
    Posts
    2,393
    #8 09-12-2021, 06:22 AM
    Mine are working fine now, Thanks to Scott.
    Reply With Quote Reply With Quote
  9. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    10,937
    #9 09-12-2021, 05:00 PM
    Quote Originally Posted by tracer1 View Post
    Mine are working fine now, Thanks to Scott.
    new caps?


    Reply With Quote Reply With Quote
  10. tracer1
    tracer1 is offline
    tracer1 tracer1's Avatar
    Join Date
    Jun 2013
    Location
    Aiken, SC
    Posts
    2,393
    #10 09-13-2021, 01:41 PM
    Yes sir. Still have a slight short in the pump wiring somewhere. Seems to lose power often. Actually don't know if its the pump wire in the motor or the cutoff switch. Happened today on the lake. Starboard side wouldn't come up even though pump would run. Open the compartment and the cap light not flashing. Moved the positive wires a little, light started flashing, worked fine. So hopefully will be something simple.
    Reply With Quote Reply With Quote
  11. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    10,937
    #11 09-13-2021, 08:21 PM
    Check for corrosion in the inline fuse holders. Clean if necessary and a little dielectric grease.


    Reply With Quote Reply With Quote
  12. Hydrilla Gear
    Hydrilla Gear is offline
    BBC SPONSOR
    Join Date
    Jun 2004
    Location
    South Florida
    Posts
    6,073
    #12 09-14-2021, 02:19 PM
    Quote Originally Posted by tracer1 View Post
    Starboard side wouldn't come up even though pump would run. Open the compartment and the cap light not flashing. Moved the positive wires a little, light started flashing, worked fine. So hopefully will be something simple.
    If the pump is running and the pole is not coming up there is either an issue with the valve body, cylinder, or Hose may be getting kinked at full deploy.

    "Move positive wires a little, light started flashing"
    Another place to check are all end connections on both positive and ground. Also check the location where the positive and ground enter into the side of the HPU.
    Reply With Quote Reply With Quote
  13. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    10,937
    #13 09-14-2021, 05:04 PM
    Quote Originally Posted by tracer1 View Post
    Yes sir. Still have a slight short in the pump wiring somewhere. Seems to lose power often. Actually don't know if its the pump wire in the motor or the cutoff switch. Happened today on the lake. Starboard side wouldn't come up even though pump would run. Open the compartment and the cap light not flashing. Moved the positive wires a little, light started flashing, worked fine. .
    Check inline fuse for corrosion as I mentioned. and obviously positive and negative at battery and where enter pump.


    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »