Results 1 to 13 of 13
  1. #1
    Member
    Join Date
    Jun 2011
    Location
    Indiana
    Posts
    16

    1999 Triton TR 21

    I'm having trouble with my live wells. I just put new electronics on my oat and the pumps stopped working. I checked and I have power at the switches. I think that when I pulled out the switch panel the switches might have gotten damaged. I called Triton and they gave me the number to the factory. I called but no answer So a few questions.....

    1. dose anyone know the part number for the switches or know where I can find them?


    2. I also i'm going to replace a couple or pumps and I haven't pulled the boat apart yet dose anyone know h\what size pumps are in the boat?



    Thanks!

  2. Member Jason Hale's Avatar
    Join Date
    Jan 2007
    Location
    Cookeville,TN via McKenzie, TN
    Posts
    6,911
    #2
    sounds like you may have pulled a wire or two off of the switches when removing them. I'd check all the wires before replacing anything.

  3. Member
    Join Date
    Aug 2016
    Location
    Knoxville, TN
    Posts
    22
    #3
    Check push butting breakers for power. If that don’t work cut the wires at the pump and see if you got 12v there?

  4. Member
    Join Date
    Jun 2011
    Location
    Indiana
    Posts
    16
    #4
    Wires are on and the breaker is in I have power to the switch. When I move the switch I don’t get any power to the out terminals.

  5. Member Danrude's Avatar
    Join Date
    Apr 2007
    Location
    Marietta, GA
    Posts
    3,531
    #5
    Here is a source for the switches http://www.marineengine.com/products....php?g=163&p=2
    750 GPH for the pumps
    Dan Burnette - Marietta, GA
    Triton 18TRX - 200 HO G2

  6. Member
    Join Date
    Aug 2016
    Location
    Knoxville, TN
    Posts
    22
    #6
    Sounds like a bad switch or the switch is properly grounded

  7. Member
    Join Date
    Aug 2016
    Location
    Knoxville, TN
    Posts
    22
    #7
    Not*

  8. Member
    Join Date
    Jun 2011
    Location
    Indiana
    Posts
    16
    #8
    Quote Originally Posted by ericl22 View Post
    Sounds like a bad switch or the switch is properly grounded



    ground is good I have a light at the switch

  9. Member
    Join Date
    Jun 2011
    Location
    Indiana
    Posts
    16
    #9
    Quote Originally Posted by Danrude View Post
    Here is a source for the switches http://www.marineengine.com/products....php?g=163&p=2
    750 GPH for the pumps

    I looked not sure if i'm looking in the wrong place but I need a 4 way witch and all i see are 3 position witches

  10. Member
    Join Date
    Jun 2011
    Location
    Indiana
    Posts
    16
    #10
    looked again and found them they are back ordered. Thanks for the help

  11. Member Danrude's Avatar
    Join Date
    Apr 2007
    Location
    Marietta, GA
    Posts
    3,531
    #11
    One thing you may want to do is check the connectors on the breaker for the pump. The spade connectors will corrode and show voltage until you apply a load then it will drop. The breakers are marked so you can find the one that feed that switch, pull the connector off and clean with alcohol and replace.
    Dan Burnette - Marietta, GA
    Triton 18TRX - 200 HO G2

  12. Member
    Join Date
    Jun 2011
    Location
    Indiana
    Posts
    16
    #12
    I will check that thanks. The pump in worked for a minute on and off and then it quit.

  13. Member
    Join Date
    May 2020
    Location
    Joelton/Tennessee
    Posts
    169
    #13
    I second checking the breaker on the pop in pop out fuses. Livewells are wired separate for the "pumps" plural to stop working there is no way both switches went out at the same time.