Currently my gear case is in the shop getting new seals and bearings.
1 I need to replace the bolts from my jack plate to my transom. Input needed on bolts!
2 I need to have my boat buffed and cleaned up.
3 I need upgrade my electronics as soon as my last ones sell.
4 I need to organize my boat.
5 I need to add a 4 bank battery charger.
6 I sent my labbed 26p bravo off to Mark to get worked.
Hopefully fishing season doesn’t sneak up on me this year
Long list. Fix issue with jack plate. Replace in dash depth finder. Get 2 props fixed. Fix sticky throttle cable. Fix hole shot plate.
fastglass1
2000 Stroker
2005 250XS
30+ Performer 3 and 30 Performer 4
I’m also going to replace my jackplate and transom bolts (grade 8 9/16” yellow zinc coated is what I use).
I also want to build a step to the front deck and add a compartment lid to the deck extension. When that is done I’ll move my tackle there to move the weight back that much farther in the boat and hopefully carry the nose better when fully loaded.
I just added side imaging last week. I now need to put it on the water and learn.
I also put 1/2 inch flexible water pipe to the front deck and ran my wiring through it. Factory loose wiring sucks.
I have mine at Hydro-Tec replacing all the fuel filters and cleaning injectors changing lower unit oil.....
Hi performance parts or a Yamaha power head visit
Hydro-Tec's web site @ http://www.yamaha-rebuild.com/
Paul Hottman Hydro-Tec's Pro staff since 1998
How long will you hold out before I see a Sho on ol yeller?Originally Posted by StrokerSmoker
Wanting to replace the toggle switches at the drivers console and bow with the rocker style, then add a livewell-water in switch at the bow. Then replace the factory Mercury cowling decals with a set of blue, silver and white
Have you seen the one's CB Marine has, they are real nice.
LeaLea
+1 on the switch package Chris puts out. Nice having the lighted rockers.
Need to replace my windshield passenger side and get my seats recovered or replaced.
Yes, that's what sparked the idea of replacing them. I like the toggles, but the labeling on the rockers is so much easier to see, especially in low light
Only thing I have to do is work on the cleanliness of the boat and motor. I will also have it serviced for this next upcoming season. I would like a rocker switch panel but I hate working with the wires on the boat.
I have had some work done on mine this year. Had the wiring system redone and a rocker switch panel put it. I am also converting from oil hubs to grease hubs since I lost one oil hub and can't find any replacements. Now when I get it back home I will clean it up and polish it so it is nice and pretty. Then wait for warmer weather or a fun time Rally to get it dirty again!
Need trolling motor repaired
Need steering helm tightened up
Need engine looked at to figure out what the new noise is, sounds like an exhaust sputter leak.
Need to replace some carpet.
Need to have seats reupholstered.
Not sure it will all get done though.
2000 Javelin Renegade 20 DC.
Strong men create easy times, Easy times create weak men & weak men create hard times. Sheikh Rashid bin Saeed Al Maktoum
In 1944 18-20 year old's stormed beaches, and parachuted behind enemy lines to almost certain death.
In 2015 18-20 year old's need safe zones so people don't hurt their feelings. "Author Unknown"
In 2021 18-40 year old's want to and work to cancel you out if you have a different opinion.
Hahaha! I need to get my seats redone also but it’s on the bottom of my list. I put a Ultrex on my boat a year and a half ago and I couldn’t live without it now
Yep some stitching is starting to come loose on my driver seat but it will hold up for another year.
Just got all cracks chips and stuff fixed on mine. About to do a super wax job when my back heals. Just had back surgery last Thursday. Install some new lights and a new bubbler in live well along with new lights in livewell. Any other ideas
Ron Fears
Stroker/300XS
1E003823
I did my Rocker Switch Panel from Chris but have some issues with livewell pumps working right it seems gotta deal with that.....
Ron Fears
Stroker/300XS
1E003823
Anyone ever ran a prop seminar to this hydromotive? I’m not in the market but it looks like a fun prop
http://www.bbcboards.net/showthread.php?t=1025637
Based on the Dia of 13 3/4" I would think it would perform similar to a good Trophy.
Reply With Quote
