Results 1 to 11 of 11
  1. #1
    Member bass boss's Avatar
    Join Date
    Oct 2007
    Location
    Wilson, NC
    Posts
    2,050

    911 CDC question

    I’ve scoured all over the internet looking for the storage length of a 911 CDC and can’t find anything. Mines a 2003 but I assume a 99-07 would be the same. I’m sure a Z-9 CDC is different. Just trying to compare this with a Z-21 storage length to see if I can get it to fit in my garage. Thanks.
    Eric Goff
    2019 Nitro Z20
    2019 Mercury 250 Pro XS 4s
    model #12500033A
    SB590181

  2. Nitro Boats Moderator BMCD's Avatar
    Join Date
    Jun 2004
    Location
    Brookeland, Texas
    Posts
    17,440
    #2
    You can safely assume less storage length is needed on a 911, vs a z9 or a z21.
    Bryan McDonough
    2023 Nitro Z21 XL
    Nitro Team

  3. Member bass boss's Avatar
    Join Date
    Oct 2007
    Location
    Wilson, NC
    Posts
    2,050
    #3
    I’m just trying to see if a z21 would fit. I know it would without talons but I’m trying to get the specifics. I have 2 feet clearance in fron of my 911 but no poles or talons.
    Eric Goff
    2019 Nitro Z20
    2019 Mercury 250 Pro XS 4s
    model #12500033A
    SB590181

  4. Nitro Boats Moderator BMCD's Avatar
    Join Date
    Jun 2004
    Location
    Brookeland, Texas
    Posts
    17,440
    #4
    Quote Originally Posted by bass boss View Post
    I’m just trying to see if a z21 would fit. I know it would without talons but I’m trying to get the specifics. I have 2 feet clearance in fron of my 911 but no poles or talons.
    Poles should not be an issue straight in, so I am assuming you are angling your boat in. I remember on the 911 trailer the side fenders extended rather far back, and that was limiting me on a rental house I was in.

    Power poles are closer to the motor, not sure if they allow you to option to power poles.
    Bryan McDonough
    2023 Nitro Z21 XL
    Nitro Team

  5. Member bass boss's Avatar
    Join Date
    Oct 2007
    Location
    Wilson, NC
    Posts
    2,050
    #5
    I have a hole in the wall cut out for my motor. It completely goes into it. The back of my boat literally goes right up to the wall. On the new boat I plan on getting, any bit of the motor than can get in hole takes package length off in my case.
    Eric Goff
    2019 Nitro Z20
    2019 Mercury 250 Pro XS 4s
    model #12500033A
    SB590181

  6. Nitro Boats Moderator BMCD's Avatar
    Join Date
    Jun 2004
    Location
    Brookeland, Texas
    Posts
    17,440
    #6
    #s posted are pretty accurate if your straight in should be easy to figure out. 24' 4"
    Bryan McDonough
    2023 Nitro Z21 XL
    Nitro Team

  7. Member bass boss's Avatar
    Join Date
    Oct 2007
    Location
    Wilson, NC
    Posts
    2,050
    #7
    My garage is only 23’ deep. That the reason for the cut out. Lol. I don’t think you understand my situation. Talons are off the back of the boat so that means less motor goes into hole.
    Eric Goff
    2019 Nitro Z20
    2019 Mercury 250 Pro XS 4s
    model #12500033A
    SB590181

  8. Member
    Join Date
    Aug 2009
    Location
    Dover, Ohio
    Posts
    5,336
    #8
    So you need a measurement from the Talon bracket (furthest point back) to the most front point on the trailer with the tongue folded?

  9. Nitro Boats Moderator BMCD's Avatar
    Join Date
    Jun 2004
    Location
    Brookeland, Texas
    Posts
    17,440
    #9
    All he needs is how far back the talons are from the sponsons. W/o poles he says it will fit, so poles are the limiting factor.
    Bryan McDonough
    2023 Nitro Z21 XL
    Nitro Team

  10. Member bass boss's Avatar
    Join Date
    Oct 2007
    Location
    Wilson, NC
    Posts
    2,050
    #10
    We’re on same page now Bryan. The biggest help would be finding out how far past the talon the motor sits. I could the subtract that off package length. If motor in down position is 2 feet past the back of talons(that are flush with my wall) that means I can subtract 2 feet off package length of a z21 and would be 22’4” then a z21 and would fit in my garage.
    Eric Goff
    2019 Nitro Z20
    2019 Mercury 250 Pro XS 4s
    model #12500033A
    SB590181

  11. Nitro Boats Moderator BMCD's Avatar
    Join Date
    Jun 2004
    Location
    Brookeland, Texas
    Posts
    17,440
    #11
    well I have power poles, and its at the lake, If I can remember i'll look at one at bass pro this weekend.
    Bryan McDonough
    2023 Nitro Z21 XL
    Nitro Team