Will a ultrex pedal fit into the recessed area on an older model (2011-2013)?
Will a ultrex pedal fit into the recessed area on an older model (2011-2013)?
It will-- BUT not all the way.
You can put a small spacer under it that is not noticeable or take some material off the bottom corners of the pedal.
LIke Mike stated. To sit it all the way down in the floor of the well the pedal needs to be placed too far forward. My 2013 does not have the E-ped I opted out of that option so it could have been set to the bottom but it would have been forward too far. I built a false floor to raise it up some and allowed it to be about an inch and a half from the back.
2013 Allison XB-21 BasSport Pro
2023 Mercury Racing 300R
Bravo FS 30P
ProMax 30P
I cut the factory recessed tray out and installed a comfort troll dlux in my 2010.
IMG_0322.JPG
2024 Xpress X21 / Yamaha 250 SHO
2022 Allison XB-21 BasSport Pro Elite / 2022 Mercury 300R (Sold)
is that an XB21?
2013 Allison XB-21 BasSport Pro
2023 Mercury Racing 300R
Bravo FS 30P
ProMax 30P
My new one is plenty big and is built lower in the front so the cables can be routed underneath the depth finder. After fishing one day with the pedal mounted flush on the bottom I changed that to personal preference.
I raised my pedal 1/2 inch in the back so I could hit the N button and the constant on without breaking my stiff foot.
Raised the front 1 inch so that the motor is now pointed straight ahead when the foot pedal is flat.. Just works and feels more natural for me.
2024 Xpress X21 / Yamaha 250 SHO
2022 Allison XB-21 BasSport Pro Elite / 2022 Mercury 300R (Sold)
2024 Xpress X21 / Yamaha 250 SHO
2022 Allison XB-21 BasSport Pro Elite / 2022 Mercury 300R (Sold)
Allison XB21 2+2, Merc 250 ProXS, 1.62 Sportmaster, Hydromotive Engineering X-OB 29
Excel 1751 Viper F4, Tohatsu 50 4-stroke, EZ-Trac trailer
FeelFree Lure 11.5 Kayak
The tray I have is about 1.5" longer and maybe 1.5" wider including the flange. I haven't felt that it's cost me any useable space when fishing. The extra length is forward toward the bow on mine. I may have set it a 1/2" further to the stern. I don't use the cup holder due to the mount for the bird being over it, but the tool holder is still useable for regular length needle-nose pliers (short, not long). Honestly, the tool holder and cup holder were of no importance to me when I bought it.
fenxVc6.jpg
Last edited by JOEALLY; 08-16-2019 at 06:54 AM.
2024 Xpress X21 / Yamaha 250 SHO
2022 Allison XB-21 BasSport Pro Elite / 2022 Mercury 300R (Sold)
Looks great, thank you for the info.
That looks great Joe. Reason I asked if it was an XB21 is because of the aluminum cross brace structure under the front deck. How did you cut that?
2013 Allison XB-21 BasSport Pro
2023 Mercury Racing 300R
Bravo FS 30P
ProMax 30P
The cut out for the new tray was very close to the original. If I remember correctly, I only had to trim about 1/2" more. Here are two pictures of the opening. I had a saw quit on me in the middle of the cut so I ended up cutting with an oscillating saw which is why the cut is rough. It cut pretty easily. The best way would be a small circular saw I think.
jpD8Yka.jpg
W5l3moD.jpg
nUtFoa3.jpg
fJzADrA.jpg
2024 Xpress X21 / Yamaha 250 SHO
2022 Allison XB-21 BasSport Pro Elite / 2022 Mercury 300R (Sold)
that's pretty sweet
2013 Allison XB-21 BasSport Pro
2023 Mercury Racing 300R
Bravo FS 30P
ProMax 30P
IMG_20181014_56776.jpg
Same Tray... Tim said he didn't have to do much more than squaring off the corners from the Factory Recessed tray...
Allison XB21 Prosport Mercury Racing 250XS with a 1.75 Sporty
How do you use the constant on and the auto pilot with the buttons below deck level ??
I'd imagine using the butt of your rod? But I see your point Mike.
2013 Allison XB-21 BasSport Pro
2023 Mercury Racing 300R
Bravo FS 30P
ProMax 30P