Hello, I have a 1993 xr6 elpto 150 hp. Serial # OD254478. I ordered a mercury water pressure kit # 79-895288A21 ( 1 to 15 psi gauge ).
Where is the correct location to tap into the motor for water pressure?
Hello, I have a 1993 xr6 elpto 150 hp. Serial # OD254478. I ordered a mercury water pressure kit # 79-895288A21 ( 1 to 15 psi gauge ).
Where is the correct location to tap into the motor for water pressure?
BEING THANKFUL FOR WHAT WE DO HAVE!!
2022 ZX200
2022 YAMAHA SHO 200
24V, 80LB ULTREX
wrong kit needs to really be 30psi , prob run pegged at wot all time and wont show excess wpsi,tee in hose at top of block just behind fly wheel that connects to poppet ,tee needs to be at top of block
.................................................. ...the scariest thing in life is the unknown ...................................
I HAD CALLED MERCURY AND THEY TOLD ME THAT MY WATER PRESSURE SHOULD BE ABOUT 12PSI AT 5500 RPM. I ORDERED THAT ONE SO PRESSURE LOSS CAN BE SEEN EASILY. I READ POST AFTER POST OF DEBATES ON THIS. LOL. BUT IF IT RUNS PEGGED LIKE YOU SAID, I CAN JUST REPLACE THE GAUGE WITHOUT HAVING TO RUN ANOTHER HOSE TO ENGINE.
I WAS CONFUSED AS TO WHERE TO TAP INTO.
BEING THANKFUL FOR WHAT WE DO HAVE!!
2022 ZX200
2022 YAMAHA SHO 200
24V, 80LB ULTREX
10-4 understood id rather see 15 ,watch any long sweeping turns at 12, if you get a sudden spike in psi could be steam = not good
.................................................. ...the scariest thing in life is the unknown ...................................
I ordered the 2 -30 psi kit. Will be returning the 1-15 kit.
Thank you
BEING THANKFUL FOR WHAT WE DO HAVE!!
2022 ZX200
2022 YAMAHA SHO 200
24V, 80LB ULTREX
.................................................. ...the scariest thing in life is the unknown ...................................
Hey everyone, just an update, i went with the 2 to 30 psi gauge like Joe suggested and glad i did. i installed Tee connector that came with kit at top of block. ( The hose that feeds the poppet valve right behind flywheel. as mercury said, i had about 12 to 14 psi at 5500 rpms. but went to 20 psi at WOT and 5psi at idle. thanks for the advice Joe!20190819_174840.jpg20190819_174825.jpg
Last edited by bassfishing101; 08-19-2019 at 07:06 PM.
BEING THANKFUL FOR WHAT WE DO HAVE!!
2022 ZX200
2022 YAMAHA SHO 200
24V, 80LB ULTREX
Glad you took Joe's excellent advice.
Dual Mercury Master Technician- for Mercury Outboards, Mercruiser and Mercury Racing at European Marine in Greenville, SC.
Still consider myself a "Marine Apprentice" after 47 years (learn something new every day).
Mercury Parts, Mercury Outboards, Smartcraft & Accessories, Injector Service, TDR Reeds- BBC Sponsor
Is there a photograph of this location on the motor available that someone could post?
"Show me the water, I will fish."
I just added 3 pics on my last post. Hope they come out ok and it helps.
BEING THANKFUL FOR WHAT WE DO HAVE!!
2022 ZX200
2022 YAMAHA SHO 200
24V, 80LB ULTREX
perfect right where it needs to be
.................................................. ...the scariest thing in life is the unknown ...................................
Couldnt have done it without your advice Joe. Thanks again.
BEING THANKFUL FOR WHAT WE DO HAVE!!
2022 ZX200
2022 YAMAHA SHO 200
24V, 80LB ULTREX
aaah youd made it somehow lots others on here coulda helped ya too , seeya JOE
.................................................. ...the scariest thing in life is the unknown ...................................
"Show me the water, I will fish."