HDS 8..Striped Bass on channel edge.
More small SB on the bottom,different location.
HDS 8..Striped Bass on channel edge.
More small SB on the bottom,different location.
~^~^~^~^~^~^~^~^~
? <?)))))><
I have 2 x HDS 10's One on in dash at one on nose of boat have them linked with sturture scan back graph shows water temp but the front graph shows everything back does but water temp (---) am i missing something?
how much you sell it for and
Some structure...
~^~^~^~^~^~^~^~^~
? <?)))))><
hey fish i have 2 hds 7 bow has a puck style ducer and transom has a skimmer style i just did the 4. update and it has totally changed unit, we were in 8 ft of water with weeds and they both were reading hard bottom @ 3 ft i really could some help getting them set up correct i also run structure scan with them linked together from start to finish what should all of my settings be @ im having the worst time with them who can help me ? can we figure it out here or is there somewhere i can call or send them out to get them dialed in we bass fish in a 18ft skeeter some rivers but primarily lakes in the northeast ALL HELP IS APPRECIATED
russ010, I have the old 522. I show arcs when trolling with outboard, but if there is no current and I am using trolling motor, I see those long lines. I am assuming they are fish, but do not know. Also, this may be a dumb question, but how does one tell the different kind of bottom on the lowrance units. This 522 is my first unit and I know it isn't near as advanced as what you have shown. Thanks
Hallo,
A few days ago I made some screenshots on a Dutch river. 4.0 is to sensitive so I made these shots with 3.5. But I used the suggestions Jason did in the other topic about problems with 4.0 and 2D Sonarview/settings. So Jason, thanks again. Next trip I will make some shots with 4.0 and I will upload the settings of those shots as well.
In the matrix you wil find the settings off the shots.
Kind regards,
Juan Gonzalez
Grtz,
Juan Gonzalez
Nitro X-5/ Mercury 135 HP Optimax/ Minn Kota Terrova 80 lbs 24 V w/iPilot & US 2/ Lowrance HDS 7/ Lowrance HDS 5m/ Lowrance X 96 TX/ Ethernet network/ Navionics Platinum plus/ Navionics Gold/ Zenith AGM batteries/ Global cranking battery
I found this same issue today and tested this: had the big motor in water when it had the streamline on graph but when I tilted all the way out the line went away. I played with sensitivity and put motor back in water and the line was gone.
Got stuck with some high wind this afternoon. Found a small cut by the dam, out of the wind on the lake I fish. After finding this, I was able to finish out my Crappie dinner on it.
New screenshots from Dutch river
Unit: HDS 7 & HDS 5m
Software: 3.5.33.217
Transducer type: Universal Sonar 2
Baitfish:
Zander (Dutch Walley):
Grtz,
Juan Gonzalez
Nitro X-5/ Mercury 135 HP Optimax/ Minn Kota Terrova 80 lbs 24 V w/iPilot & US 2/ Lowrance HDS 7/ Lowrance HDS 5m/ Lowrance X 96 TX/ Ethernet network/ Navionics Platinum plus/ Navionics Gold/ Zenith AGM batteries/ Global cranking battery
I've been out again to the same lake and they are indeed fish (caught a lot on a drop shot the next day out). I was sitting still and the ping speed was set to 17, moved the ping down to 10 and set custom depths and it cleared up a lot.
I've now got the following setting on my HDS 7 and 5...
- Sensitivity - Auto + 2% (I'll change this depending on the depth I'm fishing)
- Ping Speed - sitting still to slow troll - 10-15; steady troll - 17-max depending on depth
- 200 khz all the time, I hardly ever use the 83khz just because it works for me
- Type of Water - I rotate between General Use, Fresh Water and Clear water -- I like to rotate while moving just to see which give better returns
- Surface Clarity - Low
- Noise Rejection - Low
- Pallet - usually 13, but I like the one that shows just different shades of brown (I think pallet 9, it works great when the water is like chocolate milk in shallow water)
Other than that, If I know I'm going to concentrate on 15-25' of water, I'll set custom depths - mostly for drop shotting... but 9 times out of 10 I leave it on Auto unless it's trying to show me 20 feet of bottom and 10' of water
Today on Lake Lavon near Dallas, white bass!!
shot 2.jpg
HDS-5 Gen2 with TM260 @ 50kHz Depths are in Meters for both screencaps
HDS-5 Gen2 with B60 @ 200kHz
I have some waypoints written down on a piece of paper. How do I get those waypoints to an SD Card so that I can import them to the unit?
Bait with fish below
BAIT 2 (1200 x 900).jpg
Big pod of bait with active fish feeding
BAIT (1200 x 900).jpg
Fish on a drop with rocks
shot 1 (1200 x 900).jpg
1994 Stratos 201 Pro XL
225 Optimax
From what I gather, screen shots are saved to the internal memory right? How big is the internal storage?
Better way 001.jpgshot 006.jpg 1st is from a Gen 2 HDS 10. 2nd from same boat but on Touch 12.
your 12 shot looks pretty bad compared to the 10