Search:

Type: Posts; User: Savage

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds; generated 11 minute(s) ago.

  1. Cut out the bad section and reconnect with union.

    Cut out the bad section and reconnect with union.
  2. Replies
    4
    Views
    182

    Yes

    Yes
  3. Replies
    4
    Views
    133

    Check for a missing cross shaft bushing on the...

    Check for a missing cross shaft bushing on the starboard side.
  4. Replies
    12
    Views
    216

    Well don't I feel like an idiot lol

    Well don't I feel like an idiot lol
  5. Replies
    12
    Views
    216

    Follow the black hose from the compressor to the...

    Follow the black hose from the compressor to the bottom of the powerhead.
  6. Thread: Live 9 soaked

    by Savage
    Replies
    7
    Views
    288

    Not likely if you powered it up while it was...

    Not likely if you powered it up while it was still wet.
  7. Thread: European marine

    by Savage
    Replies
    11
    Views
    339

    Don is just a solid guy........period

    Don is just a solid guy........period
  8. Replies
    9
    Views
    292

    :thumb up2::thumb up2:

    :thumb up2::thumb up2:
  9. If 300HP is a absolute requirement, then I would...

    If 300HP is a absolute requirement, then I would just get the 300XS.
  10. The Q is a Quicksilver part which is sold in...

    The Q is a Quicksilver part which is sold in select stores.
    The A is sold by Mercury dealers.
  11. See Listings on the "Swap and Sell" "Motor Parts"...

    See Listings on the "Swap and Sell" "Motor Parts" for sale boards.
  12. Did you drain the VST also?

    Did you drain the VST also?
  13. Thread: FYI

    by Savage
    Replies
    13
    Views
    366

    Agree that the wear is probably greater on the...

    Agree that the wear is probably greater on the loaded side. Thanks for the clarification.
  14. Replies
    27
    Views
    577

    Was there oil outside of the cover? Was there...

    Was there oil outside of the cover?
    Was there oil on the lower unit drive shaft?
  15. Replies
    9
    Views
    200

    You have cooling system issues to start with....

    You have cooling system issues to start with. Possible engine damage.
    Need history and faults viewed to check readings.
    Need compression test performed.
    When was the water pump changed last?...
  16. Replies
    9
    Views
    341

    You can gauge pricing by looking at other sales...

    You can gauge pricing by looking at other sales in the "Electronics For Sale" page
  17. Replies
    12
    Views
    289

    I see where you are heading Joe......Likely #5,...

    I see where you are heading Joe......Likely #5, or #6 the harder to get to plugs, without lower pan removal.
  18. Thread: FYI

    by Savage
    Replies
    13
    Views
    366

    Total of .020 is .010 per side, or did you...

    Total of .020 is .010 per side, or did you already divide by 2 ?
  19. Replies
    12
    Views
    289

    Spark plug threads don't just get "bad" from use....

    Spark plug threads don't just get "bad" from use.

    If the steel sparkplug threads are "bad" it probably happened during a installation. The aluminum threads in the cylinder head will most likely...
  20. Replies
    12
    Views
    289

    Start with what BPS told you, get the BAD...

    Start with what BPS told you, get the BAD sparkplug threads repaired by someone other than BPS. Have the new shop double check all the other sparkplugs/wires/threads. If the motor was totally fine...
  21. Replies
    20
    Views
    371

    Brand new batteries fail also. Low voltage fault...

    Brand new batteries fail also. Low voltage fault means the voltage WAS low. Did you charge the start battery fully before heading to the lake?
  22. Replies
    54
    Views
    2,233

    Agree. I would run cylinder cancellation tests...

    Agree. I would run cylinder cancellation tests under load on the water, with Diacom software.
  23. I would change the plugs now and make sure you...

    I would change the plugs now and make sure you torque them.
  24. Thread: ISO HDS live 12

    by Savage
    Replies
    4
    Views
    291

    Check out the electronics for sale boards

    Check out the electronics for sale boards
  25. Thread: AWG wire size

    by Savage
    Replies
    2
    Views
    210

    I strip about a 1/2", then fold the copper...

    I strip about a 1/2", then fold the copper conductor in half, so the connector crimp has more to bite on. I've used red and blue, depending on the main cable size.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4