Search:

Thanks Wayne,
Can you tell from the pic if this cable is 2 conductor or 3 conductor? The way it is in 5he circuit, I assumed it was 2 but looking at I thought it may be 3.
If I buy a 4 pin...

This May be a help: check post number 6 8n this thread.

https://www.bbcboards.net/showthread.php?t=1262121

I need to extend the ribbon cables shown in the pic. It is potted to circuit boards on both ends so I will need to splice in additional cable. I have some cable from broken units but I need splice...

I broke a spring in a remote area and called in a wrecker to transport the boat and trailer to a repair shop. One of the trailer cross members was bent in the loading process and I ended up replacing...

This is the latest source for Lowrance electronics repair but I can’t speak to cost.
https://www.rudolphrepairs.com/

A problem all Lowrance repair shops have is availability of repair parts....

Check out post #6 in this thread.
https://www.bbcboards.net/showthread.php?t=1262121

I don’t have a Ghost so don’t have any experience but are you saying you can add another lift cylinder alongside the existing one?
If so that seems to be the answer.

I noticed in another post...

I tried one of the Amazon ones first but it faded in the sun pretty quick so I tried one with a zipper, didn’t like the way it twisted up so I bought the one listed in post #5 and am happy with it.

It is not unusual to have 12 volts on the hull of an aluminum boat. It results from the motor circuit grounding through the transom bolts. The only time I have seen 36 volts on the hull is when the...

Are you using the starting battery as the third trolling motor battery?

The short answer is yes, it will be fine.
If you prefer to understand the details, you might find 5he following helpful.

Sum the amp draw for all your devices from this chart:
...

The short answer is yes, it will be fine.
If you prefer to understand the details, you might find the following helpful.

Sum the amp draw for all your devices from this chart:
...

Welcome to the BBC, lots of knowledgeable guys here that are always willing to help.
Following is a link to a fellow member with a library of updates. However, I did not see the particular...

I can’t help with the 150 but I consistently get 5.0 MPG on my 115 on RT188. my fishing style is short runs and I don’t troll. I normally drive about 4800-5000 RPM.

Just click on the link in my post and download the PDF build document. It has parts list, installation instructions and requisite pictures.

See if this will open for you.
I did all my work with a 45 inch MAXXUM so I haven’t tried it with a longer shaft. That being said, I give it a good probability of working.

Me Too

WOW!!! An amazing Engineer/Designer and he obviously understands the application parameters as well.
I was concerned at first that the foot pedal was too fragile for the use environment but I’m...

It looks like an UltraVibe Speed worm. I used to fish one quite a bit in Florida but I never buzzed it across the surface.
In one picture it looked more like a swim Senko but I don’t think you can...

Look at my Kayak Transducer Wand video on UTube. There is a link to a PDF build sheet in the comments if you want to build one.

There are a lot of DIY manual poles on UTube.
I have some motorized pole video’s there too, might give you some ideas.

Size the wire for each run based on it’s amp draw and length.
This chart shows the max current for a Humminbird 12 as 2.7 (call it 3 ) amps. So the 10 gauge is huge overkill for a single unit. ...

Concerning wire size: the primary consideration for wire size in this situation is voltage drop. The chart below gives the appropriate wire size for a 3 percent voltage drop at the amp draw and...

Can’t help myself, gotta laugh at that. 😂😂😂😂😂😂

I live on a private power lake and the dock permits are very strict. For one you will not be permitted to extend into the lake for more than 30% of the cove width.
They did an aerial survey a few...