Search:

Type: Posts; User: Nutoy

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    346

    Update... Ended up being a bad connection in the...

    Update...
    Ended up being a bad connection in the boat wiring harness.
  2. Replies
    9
    Views
    346

    I have looked and looked again and can't find...

    I have looked and looked again and can't find anything unplugged.
    It's possible I blew a fuse, but all the fuses I've checked are good.
  3. Replies
    9
    Views
    346

    No sir. No 1-6 I talked to another mechanic...

    No sir. No 1-6

    I talked to another mechanic and he said the same. Possible a poor injector connection.
    He recommended I unplug and replug all my injector connections.
    Did that.

    Now my...
  4. Replies
    9
    Views
    346

    2016 Pro XS 250 2 stroke, System Fault 26

    Was idling out and my alarm started going off.
    6 intermediate beeps
    Smartcraft gauge info showed System Fault 26.
    Hit info button,,, <Air Injector>,,, Direct Injector not working properly,,,...
  5. 2016 Mercury 250 Pro XS lower motor mount cover

    If someone has a parts motor laying around.
    I'm in need of the lower motor mount cover on a 2016 Mercury 250 Pro XS 2 stroke. Drivers side if it makes a difference.
  6. Replies
    5
    Views
    254

    2014 Phoenix 921 Pro XP Been sitting a few...

    2014 Phoenix 921 Pro XP
    Been sitting a few years.
    Located in East Tx.
    $34,000
    486925
  7. Replies
    2
    Views
    461

    You are looking for a Pro Kontrol handle. They...

    You are looking for a Pro Kontrol handle.
    They are no longer made, and hard to find.
    I may have one buried around here somewhere. I'll see if I can locate it and let you know.
  8. Replies
    2
    Views
    204

    Which model? I have several.

    Which model?
    I have several.
  9. Replies
    5
    Views
    501

    To get the system totally full of fluid, it helps...

    To get the system totally full of fluid, it helps to have someone help by working the trim up switch while you add fluid. I've found those little pump bottles work well for topping off the fluid....
  10. Replies
    10
    Views
    268

    Yes. If it's not getting firm, try holding the...

    Yes.
    If it's not getting firm, try holding the bulb vertical with the outlet side of the bulb facing up.
  11. It should be smooth when you turn the shaft. Was...

    It should be smooth when you turn the shaft.
    Was there any metal debris on the drain plug magnet?
  12. Replies
    8
    Views
    446

    Hose length depends on the set up. Lots of the...

    Hose length depends on the set up.
    Lots of the newer boats have connection fittings at the splash well area that goes to the steering cylinder, then a different set of hose go to the helm.
    Some...
  13. Replies
    4
    Views
    320

    Yes, the lower can cause a lose in RPM's. You may...

    Yes, the lower can cause a lose in RPM's. You may have a bearing seizing up due to the water.
    If you are going to have a mechanic do the seals, you might as well have it taken down and inspected.If...
  14. Replies
    8
    Views
    446

    Seastar HC5345-3

    Seastar HC5345-3
  15. Replies
    21
    Views
    1,074

    This is partially true. When replacing gears, be...

    This is partially true.
    When replacing gears, be it all of them or just one, the shimming process must be completely redone. The same shims can not be reinstalled as they were before the repair....
  16. Replies
    21
    Views
    1,074

    If everything is trashed, it's going to be north...

    If everything is trashed, it's going to be north of $1500 to get it repaired. Just the gear set is going to be around $900-$1000, and the major bearings is another $400, not to mention labor.

    I...
  17. Replies
    0
    Views
    230

    Lots of 2.6 Yamaha parts

    I have a bunch of 2.6 Yamaha parts for FREE.
    Early 90's carbed 225.

    Complete motor, was running when pulled a couple years ago.
    Couple of blocks.
    Lower unit and Lower unit housing.
    Reed...
  18. Replies
    1
    Views
    104

    Fixed it. Please delete.

    Fixed it. Please delete.
  19. Replies
    1
    Views
    351

    No

    No
  20. Replies
    1
    Views
    104

    Atlas Jack Plate Actuator motor

    Need a actuator motor if anyone has one laying around.
    TIA
  21. Replies
    21
    Views
    1,074

    I have heard nothing but good on the Hydrotec...

    I have heard nothing but good on the Hydrotec guys.
    Hopefully you'll get it taken care of in a timely manner.
  22. Replies
    11
    Views
    485

    You may want to reset the oil pump to break in...

    You may want to reset the oil pump to break in mode.
    Take it easy for a few hours changing the RPMs every few minutes, then run it like you stole it.
  23. Replies
    21
    Views
    1,074

    Sounds like somebody should have done a farther...

    Sounds like somebody should have done a farther inspection when they were in there the last time.

    Usually, if a bearing or gear fails, it will take out other bearings due to the metal shavings...
  24. Replies
    21
    Views
    1,074

    My '09 HPDI did the exact same thing. I thought...

    My '09 HPDI did the exact same thing. I thought it had blown the power head, but I figured it's already shot, so I idled back to the ramp. While idling,I noticed if I gave it a touch of throttle, the...
  25. Thread: Trim motor

    by Nutoy
    Replies
    2
    Views
    206

    Do a Youtube search for Yamaha Outboard Tilt Trim...

    Do a Youtube search for Yamaha Outboard Tilt Trim diagnosing.
    Several good videos on how to diagnose the problem.

    If you are the least bit handy with tools, there is not much to the trim...
Results 1 to 25 of 485
Page 1 of 20 1 2 3 4