Search:

Type: Posts; User: rgsauger

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    521

    Tap, tap, tap is good. Thud's are bad as stated...

    Tap, tap, tap is good. Thud's are bad as stated above.
  2. Replies
    1
    Views
    364

    BassBoatSeats.com - discount code?

    Does anyone know if there is a discount code for BBC members with bassboatseats.com?

    Thanks
  3. Replies
    3
    Views
    585

    nice

    nice
  4. Are you still running stock reeds? Might be...

    Are you still running stock reeds? Might be worth checking them and replacing them with CCM or Ducas. A chipped reed will make one spit.
  5. Replies
    35
    Views
    1,510

    Hi joe, sorry for delayed response. Solid mounts...

    Hi joe, sorry for delayed response. Solid mounts are just that, solid aluminum instead of bonded rubber. Made a night and day difference in my boat handling when I ditched the old rubber. Don...
  6. Replies
    8
    Views
    522

    Have you wet sanded with 1200 and then 2000 and...

    Have you wet sanded with 1200 and then 2000 and then buffed it?
  7. Replies
    35
    Views
    1,510

    You will need power head and adapter gaskets. ...

    You will need power head and adapter gaskets. This is a great time to install solid mounts if your boat runs over 60 or so
  8. Replies
    11
    Views
    2,003

    I built my Shadow as a cap off from stem to...

    I built my Shadow as a cap off from stem to stern. Love it!!! My build is in my signaturr. Good luck
  9. Replies
    12
    Views
    464

    90 is pretty low

    90 is pretty low
  10. Replies
    12
    Views
    464

    Stock compression should be around 120. Have you...

    Stock compression should be around 120. Have you done a thorough decarb on it? You can cut the heads and take it up to 145 or so and boost the torque and midrange but your will have to run premium.
  11. Replies
    3
    Views
    574

    Measure your prop to pad and report back

    Measure your prop to pad and report back
  12. Replies
    10
    Views
    1,054

    That's from exhaust heat and heavy minerals in...

    That's from exhaust heat and heavy minerals in your water you run in. No big deal
  13. Replies
    4
    Views
    745

    I had a 17 alum a craft hat was a great boat. ...

    I had a 17 alum a craft hat was a great boat. Similar to yours. 50hp OMC. Miss that one!
  14. You are probably fine but if it's gonna haunt...

    You are probably fine but if it's gonna haunt you, then yank it and do over.
  15. Replies
    4
    Views
    364

    Agree. Sell it outright

    Agree. Sell it outright
  16. Replies
    2
    Views
    256

    Agreed on lower crank seal. Yank the powerhead...

    Agreed on lower crank seal. Yank the powerhead and repc from the bottom. Not too bad of a job
  17. Replies
    3
    Views
    490

    Can you post pics?

    Can you post pics?
  18. Replies
    23
    Views
    3,581

    I have used System Three with very good results. ...

    I have used System Three with very good results. The general is fine but their Silver Tip wets out better.
  19. Replies
    23
    Views
    3,581

    So ditch the half measures and do it right, bud. ...

    So ditch the half measures and do it right, bud. Injecting glue or resin is a shortcut for sure. Do it once, do it right, be proud of your results!

    Any chance you could bolt, glass, or glue in...
  20. Replies
    3
    Views
    232

    The little scoops made a huge difference for me...

    The little scoops made a huge difference for me before I got low water pickup. I plugged the two top holes on the sides. Tapped for 5/16
  21. Replies
    23
    Views
    3,581

    Post pics

    Post pics
  22. Replies
    23
    Views
    3,581

    If you can get to the back side, you might pull...

    If you can get to the back side, you might pull your helm and gauges. Then cut out the old wood with an oscillating tool and glass in a new piece. Glass work is not that hard to do. Boat builder...
  23. Thread: Im stumped !

    by rgsauger
    Replies
    6
    Views
    532

    Shucks, can't remember. But I think we swapped...

    Shucks, can't remember. But I think we swapped trigger and stator on your pro Max and that did it.
  24. Replies
    3
    Views
    306

    The CCM boys and good people. Good luck on your...

    The CCM boys and good people. Good luck on your build. Mine is down for same reason...#6
  25. It's not hard but can be a pita if by yourself. ...

    It's not hard but can be a pita if by yourself. Read all the links and watch the videos about water pump replacement. You have to line up the driveshaft, the water tube, and the shift shaft. Not...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4