Search:

Type: Posts; User: ces23702

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    449

    Doubt you'll find too many OE parts left. I've...

    Doubt you'll find too many OE parts left. I've got the same boat and really haven't been able to locate much of anything. Not too hard to make one though.
  2. Replies
    5
    Views
    437

    Check Overtons. Caught mine on sale for 50% off...

    Check Overtons. Caught mine on sale for 50% off last year. Also before you buy you can order a free carpet sample card to match weight and color.
  3. Thread: 1996 201

    by ces23702
    Replies
    4
    Views
    307

    Not sure what year they went all composited but...

    Not sure what year they went all composited but believe it was around 96-97. My 95 has laminated stringers which are foam filled. The transom is still wood I believe, hadn't needed to get into that...
  4. Gel coat repair kit for the keel. I believe a 97...

    Gel coat repair kit for the keel. I believe a 97 is all composite so no biggie. If the floor is wood it has resin over it that stress cracks over time where it is thicker and used as fairing. Get...
  5. Replies
    8
    Views
    687

    I added one to my 95 201 with no issues. One of...

    I added one to my 95 201 with no issues. One of the best things I've done to the boat. Easy once your past that first cut.
  6. Without fuel in the filter the bulb cannot pull...

    Without fuel in the filter the bulb cannot pull enough to compensate for it being empty. Could have a air leak not allowing fuel to be pulled through the lines. Bulb could be bad also.
  7. Replies
    3
    Views
    298

    Make sure the connections are clean and not...

    Make sure the connections are clean and not corroded first. Then check with a ohm meter across connectors and see if you get a reading. Resistance means the sender is working although may not be...
  8. Replies
    1
    Views
    209

    There should be numbers on the edge of the...

    There should be numbers on the edge of the bearing races. If you have a trailer supply nearby just take them everything and they'll match it up for you. Mine ran me about $12 a wheel for bearings and...
  9. Replies
    26
    Views
    1,975

    Before a crack is repaired it needs to have a...

    Before a crack is repaired it needs to have a small hole drilled at each end to prevent the crack from spreading.
    Rivets can be re-bucked to attempt to tighten them or replace with closed end blind...
  10. Replies
    26
    Views
    2,014

    Walmart also carries a file folder that holds...

    Walmart also carries a file folder that holds 3700 boxes. Lid fits on it with boxes so storage out of the boat is a nice option also. Located in the office section.
  11. Replies
    21
    Views
    6,855

    You can also get a piece of 1/8 textured abs...

    You can also get a piece of 1/8 textured abs plactic from a car stereo shop and cut your own.
  12. Replies
    1
    Views
    566

    They work great and also come in aluminum and...

    They work great and also come in aluminum and steel that use a pop rivet type tool called a thread setter. Make sure to use thread sealer on the screws so that they dont corode and cannot be remove
  13. Replies
    10
    Views
    2,817

    I've got some pics with measurements on my...

    I've got some pics with measurements on my Motorguide but its telling me they're too large to post. Anyone know how to downsize them?
  14. Replies
    10
    Views
    2,817

    On my Motorguide I was able to drill new holes in...

    On my Motorguide I was able to drill new holes in the upper half of the mounting bracket to make it fit. I know it's not the same tm but i can get you some measurements if you need
  15. Replies
    10
    Views
    766

    As others said check connections. Could be the...

    As others said check connections. Could be the switch itself. It uses different contacts for auto and manual so may have lost the auto contact for that switch. Either way you need to access the back...
  16. Replies
    2
    Views
    323

    On my 95 201. At the console Power switch on....

    On my 95 201. At the console Power switch on. Master Aerator switch to fishing. At the bow port and starboard aerator switches cut those on or auto with timer switch between them.
  17. Thread: Stratos 21xl

    by ces23702
    Replies
    9
    Views
    320

    If you have 24v at the plug the next issue is...

    If you have 24v at the plug the next issue is trying to recreate the voltage loss. Access the wires behind and flex them one at a time while watching the meter. If voltage maintains at 24v you may...
  18. Thread: Stratos 21xl

    by ces23702
    Replies
    9
    Views
    320

    Check your connections at the batteries and at...

    Check your connections at the batteries and at the bow. Usually the bow plug is the culprit on trolling motor issues. Test with a volt meter at the bow checking the plug first. Follow the circuit...
  19. Replies
    8
    Views
    2,448

    As far as materials go try and find a fiberglass...

    As far as materials go try and find a fiberglass supplier. The epoxy can be 30% cheaper if you can buy under a business name. The cloth by the yard will be significantly cheaper as well. I used foam...
  20. Replies
    8
    Views
    2,448

    I just did the floor in my 95 201. The rear isn't...

    I just did the floor in my 95 201. The rear isn't too bad to replace. It's 1/2 " marine plywood. Take that screwdriver and tap all around to find what bad and whats good wood. Remove all rotted wood....
Results 1 to 20 of 20