If I have the merc monitor and the gateway (Backboned to my Solix), does either one of them show estimated speed from this (Pitot) sensor or does it only go to the ecm for it's purposes?
Type: Posts; User: Travis
If I have the merc monitor and the gateway (Backboned to my Solix), does either one of them show estimated speed from this (Pitot) sensor or does it only go to the ecm for it's purposes?
Don, I also found the water line that feeds the Pitot sensor to be clogged. Cleared it out but I do not run a speedo off the tubbing so I removed it and the Tee and ran the line from the L/U straight...
Will try that. I basically ziptied the unit to its pigtail and used a cut piece of tubing to run back to it from tee. One last thing, I noticed lots of orange "dust" under the cowling all over the...
A good friend is better than all the money in the world
Yessir, I am getting a refund on the second sendor so I want to order another and give it another shot. The line, Tee and fittings all look good and clear. Must have been two bad sendors. I do feel I...
After running again at idle, with a new sendor for the analog gauge, I saw a little water pressure. So I then changed out the second 8M0059531 sendor that was not showing any pressure with the...
I hope I damaged the 8M0059531 with the air hose and that is why I still show no water pressure. With the line off in the water(Lake) the other evening, I had a good stream of water coming from the...
Yes and the 8M0059531 I installed after I intially had my first overheat alarm and it was a quicksilver item in its packaging. I T-eed it in just as shown in your link in the above post but it never...
This is why I asked the difference on the two part number sendors.... Is it just the threads? The other part number is for a strainer as mercury calls it. In my mind this is all the same topic. No...
Those in the link I installed when I installed the second water pump kit. That's what I'm saying. I've tried it all.
Also, is the 8M0183166 mercury inline strainer another filter I need to check and clean? Is it the intake for the cooling system?
So is the only difference in those two sendors the threads? I think I misread your post about which one to use and see now that you meant to use the one for the 150 4s for the tee application and the...
So I see the threads are for the block for the correct sensor. Does Mercury make the quick connector to fit these threads so I can have both analog and the digital?
I have the tee, adaptor and fitting all Mercury parts but I used the wrong sendor looks like and the analogy in my dash appears to not be working all together. So I need to order the 8M0142696
Don, I teed it in like you had on a post to use both analog and the Merc monitor(plugging up to ecm) I used the 531 sensor tho as in that post and that's the wrong sensor for my 250 looks like...
Which is the correct sensor for my engine? 8m0142696?
Or 8m0059531?
So ran it in the lake today, the pee from the water line from the block was little stronger for sure. Motor ran up to low 160s and would come down to low 150s and stay. Give a little throttle.......
Have both. I'm having doubts in my analog as it's not working when I put the air hose to it but the one plugged to my ecm is registering psi when I put a little air to the water line.
Ran it in a tank today. Water was up to the cavitation plate. Pee was good.... Ran only three minutes maybe, temp went up to 152 then started dropping but had zero water pressure on Merc monitor. I...
It helped some. I think I just had to much of a spill for too long and it's just dyed the carpet out. Maybe the sun will do it's thing like it does for the worm dyes.
I will give it a try. I have tried krud cutter as it foams like shaving cream but that did not work. I have scrubbed the carpet so much in the area it is starting to look bad.
Have not been able to tow the boat to try at a ramp as I cannot replace mid section cowl till the threaded insert and bracket arrive from mercury that broke while going in to inspect the lower...
The shaving cream seem to get it?
Na, didn't work for me. That oil has that green/ yellow look. after trying everything I am just curious if the sun will take it out like it does the worm dye.
https://i.postimg.cc/bN6sX8Ss/wp-upper-bottom.jpg