Well..mystery solved!! When I did the water pump the shiftrod was turned..screwing the rod into the gear case 2 additional turns...shorting the rod about an eight of an inch. Sinced the rod was...
Type: Posts; User: billyboy
Well..mystery solved!! When I did the water pump the shiftrod was turned..screwing the rod into the gear case 2 additional turns...shorting the rod about an eight of an inch. Sinced the rod was...
Thanks Gearcaseman for the info, and yes I am turning the output shaft..otherwise
the clutch dogs couldn't ingauge the ring gears. I think some how I messed up reinstallng the lower unit, because...
Yep..my linkage from the lower unit is held in the shift-rod lever by a pin..otherwise when shifting to forward the shift rod would be pulled loose from the shift lever. Checked the adjustment on the...
Just took the old girl (91 xp200) out, and no reverse...did a water pump job, but didn't change any linkage settings. If worse case, and I have to replace the clutch
dog what other parts do I need...
Hey!! Thanks for the info!! http://www.bassboatcentral.com/smileys/USA1.gif
Is a 97 88hp, and a 115hp Evinrude the same except for the carbs?
Thanks!
Well I checked the post as you said. I learned looper/closed deck engines didn't come out untill 93..Hmmmm.
Then I read..They were open deck non finger ported loop charged motors until 93 or 94 when...
I except no one wants to type that much, but what is finger porting, and whats the
difference in open, and closed deck.
Is a 91 xp200 a closed, or open deck..finger ported, or not?
Thanks!!
...
Answered my own question!! http://www.bassboatcentral.com/smileys/doh.gif
Thanks http://www.bassboatcentral.com/smileys/USA1.gif
Modified by billyboy at 11:19 AM 6/6/2007
I had the same problem with me 91 201 pro/200xp. I removed all but one bolt holding the motor to the jackplate, and lifted the engine straight..then redrilled the holes in the jackplate. Worked fine!...
If I'm not mistaken Rusty told me to not go over 5400.
Rusty, Seahorse, anybody!!!
What is "Power boost cooling?"
Rusty..what is power boost cooling? Is also true for the XP200?
Thanks
I wouldn't trade my ole 201 for nothing!! There are no easy monthly payments to make, and she gets me to where the fish are just like a new $45,000 dollar rig does.
Also as to the gas tanks, they...
My 92 201 has the tanks behind the seats..she rides high, and dry!
There ya go!!!! Sounds like a deal to me!!
Was talking to my neighbor the other day about my trim relay going bad, and he told me O' Reilly's, and NAPA auto parts carried them.
#mine were #18-5705 $15.00
Wonder how they'd work?...
I'm looking for a steering cylinder for my boat, and need to know which seastar cylinder fit my 91 xp200? http://www.bassboatcentral.com/smileys/USA1.gif
I use CPES on my 92 201 pro. First I cut the cap off the transom, and drilled holes about 3" apart then 4 holes forming 2 X's side by side. After all this I poured it full of the CPES then let it...
So that's why the 200 pounders were always empty!!
Do you know how long it takes to burn down a perfectly good helecopter?
Answer> When you find out the 200's empty just keep running. It's already...
Nope!!! You ain't the only one. I like to move mine from side to side also.
If you're running the prop with a blow out ring..then take it out and try it!
Does anyone know if the water level in lake livingston is back up yet? Heard you could only put in @ Kickapoo creek?
I've got the same jig as you..92 201, 91 xp200. Mine tries to porpoise too..till you either trim dowm, or add more throttle. Mine is set @ 3 1/2" below the pad....
so setting it higher will stop it?
I know it's heresy to advicate anything but BRP products...but..I've used seafoam for a long time without a single problem. No carbon, plug fouling, or carb cleaning!
I also use XD100 though..!