You can create two custom palettes for the standard map.
Type: Posts; User: sparkertx3
You can create two custom palettes for the standard map.
I have a 300R, but my dealer doesn't specialize in racing products. He had the part. I have it on a Fury, I'm sure it's good for all Mercury props. And yeah, they say to still check the torque...
The single big washer/double nut system shown in the photo is new, each nut is to be torqued to 85 ft-lbs.
https://community.brunswick.com/area/blog/grab-the-torque-wrench/article/16541
I got...
Mine came with a Torquemaster and a 25 Fury 3-blade. Haven't run it yet. Actually don't have it yet, being rigged.
It's a bigger lake, the fish are bigger and there are more of them, but the facilities are sparse. Norfork is much better for the tournament although Bull fishes better. Norfork has been pretty...
I have AT1, I upgraded to 23.3, experienced the freezes, downgraded back to 22.1.
About 15 minutes into my next trip, I re-installed 23.3. To me, there was enough improvement in what I was able...
I updated to 23.3, big improvement, got tired of 2-4 freezes per trip, rolled back to 22.1, the first morning using 22.1 by about 8:30 I put the 23.3 back on, the difference in imaging is worth the...
I replaced mine on the first recall in early 2019, but I've heard of much later year models having the same problem. Surely they've fixed it on motors built after late 2018. Haven't they? :doh:
On my Lynx/300, the difference between 24 and 25 Fury is about 2 mph (77/79), about 1 mph less when it's hot. Turning 6200 on the 24, 6000 on the 25, when it's not so hot. But it's a Lynx and it...
Funny, mine would either gall up and be hard to remove or they would loosen if I didn't put them on tight enough. Anti-seize solved both problems.
It should show "1" at the low point.
My lives share waypoints perfectly when I turn them on, after about twenty minutes they stop sharing. Map still shares between two units but not the third, after a while. If I reboot a unit,...
I have a lot of waypoints with the same name. If they aren't on the same position, leave them alone unless you don't need them. If you have two on the same spot, then I would delete them as I came...
Sounds like you only need the new module to get the fish reveal feature (with HDS Pro - the new HD transducers without fish reveal plug in the units directly.) Not sure if any older units can use...
I stop all my transducers except AT. The flash lets me know if I forgot one.
If it's Smartcraft it may have lost its calibration. Recalibrating mine was simple once I figured out which buttons to hold down to get the gauge into calibration mode.
Not much gain from the 250 to the 300 Pro XS, not worth the cost in my opinion. I wouldn't do it again.
The 300R might be worth it.
There is a calibration that is easy to do once you figure out how to get it started. It varies a little depending on the type of gauge. Once you are in edit, it's trim down, save, trim up, save,...
I believe deleted, but not purged, waypoints and or routes and trails will still transfer to other networked units when powered up. So they are deleted from one unit but still available to be...
On your speed issue, you are getting less than a 50 hp increase between a 250 Pro XS and a 300 Pro XS. On my boat it's about 3 - 4 mph between the two. I can hit 6200 with a 24 Fury at 75, and near...
2D stops in standby, downscan and sidescan don't. When you bring your unit out of standby you can see the 2D restart. The others just keep going.
In my experience, putting a unit in standby does turn off 2D sonar, it does not turn off downscan or side imaging transducers. And mapping cards are still active.
Your transducer angle may need adjustment. Try tilting it up slightly.
Do we have to buy one of those plastic measuring boards the kayak guys use?
Surge, I run a 26 on my Lynx/300. You need to drop some pitch for a 250. 25 or maybe 24, two holes plugged as mentioned.