Search:

anyone fish this body of water? Me and the family heading up Tuesday and from what I gather it's mainly a ski/recreation lake. Just wondering where I can set a hook.

i've had a few impacts (fishing in South Louisiana, you're bound to hit something from time to time) and had one earlier that morning of fishing. Nothing outrageous, but enough to jog the boat. For...

Apparently not. Every time I make a claim, they find a way to deny coverage. Case in point, lower unit just went out and Progressive is denying coverage saying it was lack of me checking my bolts on...

I'm running the mixture. I just need to get past tomorrow and then I'll drop the tank and clean it out. Appreciate the help.

So do I run the risk of hurting the motor by just running the TW3 until it's almost out?

Not realizing, I grabbed the red label 2 stroke quicksilver oil from Academy my last trip. I ran my 2009 Pro XS about a month ago with no issues but today I bought some DFI oil. Is it ok to mix?...

damn fine job

I caution at moving the hotfoot forward as far as possible. I did it and it put my throttle cable in a bind without me knowing. Went to leave the launch and the hotfoot stuck with the cable binded. I...

Is this old info?

Also, i say jackplate and transom, but i do have 1 powerpole, so i have the brackets actually between the jackplate and transom.

What types of bolts, washers, nuts to use if...

Had a quick trip saturday, and as i was putting the boat up for the night, I noticed i could see light between the jackplate and transom. Obviously, i need to tighten the mounting bolts, but are...

I'm not sure i'm following a 100% but i just worked on 2 LNG projects over the past couple years. One in Freeport Texas and another in Cameron, LA. Both land based.

13 fishing concept A & C are the reels that I use

Seaguar invizx is what i use

I use KVD's line conditioner when spooling, but hadn't tried spraying it the morning of fishing or anything. I'll give it a try.

This may be a newbish question, but for the life of me, i can't figure this out. I think i'm spooling it onto my reels correctly, but maybe i'm not. But I will put on fresh line, and within a week,...

Do i clean the hub, then apply the rtv in the grooves and then press the strips into the rtv? Do i have to let it sit and bond for a period of time? Or just follow the instructions on the rtv tube?

Adhesive....thats the word I was looking for :laugh:

I have a lower unit with a fat shaft. When taking off my prop this weekend, one of the spacers that fit in the grooves of the hub came out with the prop. I know most of the spacers somewhat move from...

It's a club tourney, so we are going up there on the 21st and fishing until Sunday. These guys tend to all fish on top of each other or fish the same area. We are launching at Green Acres (I think)...

What is this boatlanes card being talked about? I'm making my first trip to TB at the end of the month. The only chip I have right now is the LA Geaux card, which I know won't work up there, so i'll...

Here's what i have. I just realized that I was looking at the wrong cable thinking it was from my motor.

Basically, the left hand side the switch goes to my battery. The right hand side (next to...

Is the on side the output side? I'm assuming it would be as the power us being fed into the switch from the battery, and the exiting the switch to the dash. I'll post a picture of what I'm looking at...

Bump. Better explanation of what I'm not understanding on the electrical/trolling motor board

I apologize for not understanding, but this is what I believe is what I have. I get what you're saying about the input side being to my common, but are you saying I have to disconnect the wire from...

+1

Bought 2 yesterday

Ranger 09 Z520

All rangers pretty much have this switch. When looking at the switch in the bottom right, what lug would be considered the input? I have a battery cable going from my crank to the...