Search:

Stud Assemblies, Camloc 1/4 Turn Fasteners On Alcoa Fastening Systems - AFS

Whatever floats your boat, I've had both trucks and vans...only four wheel drive is superior. Up to class two hitch class the newest minivans work just fine, I've never had an issue on any...

I always get a kick out of men who need to justify their truck, don't get me wrong I used to hate minivans...they were slow and bouncy and had a stigma.

Out of necessity I needed one, three kids...

I tow a Lund 17' ProSport with a 200 Merc and a 3500pd rated single axle trailer behind my 2011 Caravan with the 3.6L 284HP V6. Full of camping gear, three kids and two adults it is fine.

I drive...

Now that's using your noggin!

:thumb up2:

Low pressure pump diaphram torn or a one way check disc damaged will cause similar symptoms, I have the same motor but a 91/92 year model and it ran fine for awhile and did the same thing, found out...

I would never bring my DSLR in the boat, I use a pocket sized point and shoot as losing a $100 camera or getting it wet accidentally wouldn't be the end of the world. My point and shoot has 12MP the...

What kind of prop you running?

I coated my pressure treated bunk boards with contact cement and let it dry, this creates a thick rubber coating that seals the wood so no leaching issues.

Once the rubber cures it wont stick to...

When I hear "multi-specie" I think Walleye boat as well, up here that is defined by Lunds, Crestliners, Yarcrafts, Lowe, Ranger and a few others.

I am not interested in exclusivity at all, I love...

I see a few bass boats being posted in this forum and I'm pretty sure most people would not define a pad equipped low freeboard bass hull as "multispecies"...of course I know you can fish for...

Actually the AL is cooler on the feet than the carpet, I carpeted the front section again after replacing the wood with AL only becuase the kids often sit up front. I'm going to remove it and make...

My 1998 Lund 1700 ProSport before the 10" HydroJacker install, diamond plate has replaced all wood in the boat and the transom is now pultruded fiberglass lamination to handle the extra HP as its...

Just an FYI, the green "wicking" Loctite product is what I use. It will air cure as it is also used to seal porosity in castings etc. I just put a drop on the buddy after its installed and it wicks...

Same stuff essentially, just different thicknesses to accommodate various gaps. I doubt you could tell the difference.

Plenty of thread there, the nut on mine is twice the length of a stock Merc nut. Here is a pic of my 25" Renegade mounted on a 2.5L 200HP Merc, you can see how small the barrel is compared to the...

I'm running a 25" Renegade Bass on my 200 Merc, the prop shaft is drilled for a cotter pin and the nut is different. Not sure if the tapered spacer is different than the stock Merc one but it is...

Have you considered a home made hole shot plate to cover the opening at the bottom? Its a pretty common performance mod for deep jackplates on short transom performance boats, it has the side benefit...

Nothing works on dried superglue.

I use Ronsonol to clean custom made hydraulic hoses of particulates before installation, I always keep some in the garage.

Those Maglite clips also hold a Frabil Hibernet perfectly!

My 1991 Merc 200 XRI retards the timing at 5600, I think you will find shooting for that rpm as the best speed rpm. Ive tried a bunch of props on my combo and revving it higher didn't gain me anymore...

Don't see why not, you would be surprised how fast it works...even uphill. In the summer the rope dries out completely in a couple of days even if there is a quarter inch of water left in the bilge....

Never seen this posted anywhere, been doing it for years.

Insert a short length of cotton rope into the bilge drain hole during storage, push enough inside of the bilge area to sit in the bilge...