So, I could confirm if there is a little interference on my scout by simply turning my forward AT2 off to see if that "shimmer" goes away on the scout. I'll check it out tomorrow.
Type: Posts; User: n8cas
So, I could confirm if there is a little interference on my scout by simply turning my forward AT2 off to see if that "shimmer" goes away on the scout. I'll check it out tomorrow.
I did a quick video to confirm no interference with my HDS lives: https://youtube.com/shorts/mARXoBtrbec?si=fFt9QUL2RA8fKJU4
Please don't critique my wiring. I wanted to make sure it all worked...
Thank you Sleepy!
I got out on the water this weekend to test my setup. It worked very well! With my 2 HDS lives (not Pros) and the blue wires connected on both of my AT2s I did not experience any interference...
Thanks again, Marc! I missed it when searching through the forum.
This is great! Thank you very much. I've heard people say how they like to see the splash of their lure - but I'll probably be mounting my forward AT2 lower for deeper water fishing and for rough...
I'm sure of few people have experimented on different heights to try to get the best possible image. I've heard as low as 6 inches above the Trolling motor all the way up to 10 inches. I am running...
Thanks for sharing. This is always a big concern for me as I like to fish throughout the winter. Water temp was 42 degrees last time I was out! Apparently the water dumps out quickly when you exit...
Anyone see the ads for the FXR Pro Fish line with F.A.S.T. float assist insulation in the gear themselves to help keep the person floating if they fall off the boat and go in the drink?
I need...
I think I fixed the problem. Did some research on YouTube and saw this helpful video from Russell Marine:
Active Target 2 "NO SOURCE" Fix (youtube.com)
Restore Defaults on all 3 of my HDS...
When turning on my TWO new AT2s for the first time / updating them / testing them to see that they both work - I only got one source to be recognized by my HDS lives. When I first booted up, it...
Thank you very much for all the helpful information. I'll report back once I install. I will be manually turning off the 2d sonar in the ghost TM since I probably won't even need it (have space for...
That looks like solid evidence right there, but I might test it out before trading in another unit. So, in essence, that toggle setting tells AT2 to send info / current through the blue wire that...
the last two posts contradict each other. Only 1 way to find out!
according to this post by JJ in the thread "How good are two AT2's" , I think as long as those two blue wires from my two AT2s are touching, I should be good. I HOPE so.
"I run (2) AT2s...
I do not have HDS Pros, I have HDS lives. I hope that wiring the two AT 2's blue wires together will sync the ping without the need to upgrade to a HDS Pro at this time.
I watched your part 1...
I'm going to be installing my 2 AT2's this weekend. To make sure the ping sync works properly for both AT2's I need to wire them (blue wires) together correct? That should be simple enough. I need...
Thanks. Hope the chart installer works on a mac
Does a 5 year old card ever cause rebooting issues? Or is that mainly a power source issue?
Not sure if this is the right place for this post. It falls under electronics for me, but if it should be posted somewhere else, please let me know.
I bought my Navionics Hotmaps Platinum...
Don't most people run more than just their FFS with 1 dedicated electronics battery ? Is that the suggested method ? -- run the AT 2 on a separate battery from the rest of your electronics?
I have 1 HDS12-live at the console, 2 HDS12-lives at the bow and 1 AT, but I'd like to upgrade to 2 AT 2's. Thanks for sharing your set-up and advice - very helpful! I might need to get a new...
What's the voltage recommendation for that many graphs and multiple Active Targets ? In other words, which expensive 1 dedicated battery do I need to buy to strictly run JUST all these electronics? ...
I was out this past Sunday and realized I used the map a lot to follow my Track a lot, so I'm not sure what I'm going to do. Can you split a HDS (pro or live) so it shows Active Target sonar AND...
:thumb up2: