Ot051231 Manual calls for NGK BUHW-2 which is NLA according to Oreilly. What plug do I go to from NGK? Have NGK BP8H-N-10 which is 115 hp plug but don't know if that is the best choice. Thanks for...
Type: Posts; User: moldman
Ot051231 Manual calls for NGK BUHW-2 which is NLA according to Oreilly. What plug do I go to from NGK? Have NGK BP8H-N-10 which is 115 hp plug but don't know if that is the best choice. Thanks for...
Thank all you guys for your input. It is appreciated.
Used this for years on fiberglass and painted cowlings but can't seem to find it anymore. I could sand to 1200 and go to this compound and get good results. What can i get that's conparable that...
Thank you for the info. It is much appreciated.
SN OG666001 Engine mounted oil reservoir will not stay completely full. At ramp I start the engine and barely open the cap on the reservoir until it fills. The next day the oil has gown down to the...
Thanks for the info. I appreciate it.
Serial no. 0T273979. Having intermittent problems with detonation module not letting engine start. Unplug it and it will start. Plug it back in and it will start. Starts at the turn of the key. Can I...
SN 0T119988 2000 90hp Mercury 3 cylinder 2 stroke. What are the dimensions for the crank main journals and for the rod journals? I have one I need to polish to see if it is usable. Couldn't find...
Just finished a 1998 3.0 225 EFI to go on my 1995 Cobra 201D that I restored years ago. All bores cleaned up at .015 so that tells you how long one of these engines will last if you take care of...
Borrowed a crank sensor from a buddy and after installing it the cylinders are firing correctly. Turned on the water, hit the key and I don't think it made a complete revolution before it started. I...
When I first tried to fire this engine and it didn't start I checked stator voltages at the CDM's with the Mercury test harness. With CDM's disconnected they averaged 155 at cranking speed. With...
Sometimes it shows no.1, sometime no. 4, sometime no.2, sometime no. 5, back to no. 1. Showing different cylinders when I'm hooked to no. 1. I set my crank sensor to .040.
Got back to my project today. Checked all my grounds at CDM's and all good and ran 2 separate grounds(1 to each side of mtg plate)from battery ground on starter. Marked my flywheel for TDC of all...
I'm looking for a compound that's just as good as 3M Marine polishing compound 06044 and maybe cheaper. I have had great results with the 3M on my fiberglass bass boat and today I used it to polish a...
Read the manual again and looks like I put the right plugs in.
The manual listed NGK BPZ8H-N-10 or Champion QL77CC. Parts store didn't have NGK so I went with Champion.
Is 1141, 1161,1132,1117,1147,1140 close enough. Crank position sensor ohms 1202. When I check spark plug wires with a timing light some have intermittent fire and some have no fire. I guess I will...
Thanks JOE54 and EuropeanAM. Appreciate both of you guys.
OG666001 Svc manual 90-822900R3 says check between grn/wht and wht/grn but stator does not have those colors. Has grn/red, grn/yel, grn, grn/blu, grn/org, grn/blk. These are the colors the...
Do you need the whole assembly or just the spring loaded pins? I have some from my Cobra 201D.
My computer is showing this site as insecure. Are my settings too high? Long time member and have just recently seen this.
Thank you for that info.
Black and one piece driveshaft.
Do not have engine this came off of. Part no. is 1689-840470-C and is stamped 06C721 on top. Fat shaft. Has 4 front water inlets and torque wedge built into the skeg. Anyway to tell approximate year...
Thanks for the replies guys. It's a 6 switch panel for bilge, livewell, and a few lights. I'm not worried about it in the least. I'm using negative for ground and positive for power.