Search:

Type: Posts; User: Danrude

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    116

    If the auto bilge pump is one of the type that...

    If the auto bilge pump is one of the type that has a sensor instead of a float then you problem may be the pump! The sensors go bad and they will turn on randomly!
  2. Replies
    19
    Views
    703

    Are these motors being troubleshot on the boat or...

    Are these motors being troubleshot on the boat or removed and taken to the shop? The electronics on these motors will monitor the voltage and if the voltage on one battery drops below a certain point...
  3. Replies
    5
    Views
    179

    When the lift assist shock goes bad sometimes it...

    When the lift assist shock goes bad sometimes it breaks the crutch so you may need both!
  4. Replies
    15
    Views
    311

    This is a good source for the various switches on...

    This is a good source for the various switches on those panels. https://www.marineengine.com/products/accessory.php?in=1907891
  5. Replies
    15
    Views
    311

    There should be a diode in the circuit and from...

    There should be a diode in the circuit and from your picture I do not see it! You can get a wiring diagram from the Triton web site that will show the hookup! don't worry about the dates show on the...
  6. Thread: Spark Plugs

    by Danrude
    Replies
    5
    Views
    221

    You should run the optional QC10WEP plugs, you...

    You should run the optional QC10WEP plugs, you will need to change to the ETec T-stats part # 5005440!
  7. That part is a check valve the Pressure regulator...

    That part is a check valve the Pressure regulator it restricts the flow of oil back to the oil tank. If you are going to gamble then purchase this...
  8. Replies
    25
    Views
    1,322

    https://www.nutterrodandreel.com/

    https://www.nutterrodandreel.com/
  9. Replies
    2
    Views
    134

    There is a 20 amp in line fuse in the line that...

    There is a 20 amp in line fuse in the line that feed the panel, you should find it on the + side of the cranking battery about 5 or 6 inches from the post.
  10. Thread: low battery

    by Danrude
    Replies
    18
    Views
    425

    A healthy battery will read approximately 11.75...

    A healthy battery will read approximately 11.75 volts when it is completely discharged which tell me you have a bad battery. If you are getting 9 volts I would think you have some dead cells. one way...
  11. Replies
    6
    Views
    227

    When you are performing the injector test with...

    When you are performing the injector test with the software and the motor dies it indicates you have either a bad injector or low compression on one or more cylinders! The first thing you should is a...
  12. Consider upgrading to the Wet Bolt kits....

    Consider upgrading to the Wet Bolt kits. https://www.etrailer.com/search/Dexter+Wet+Bolt+Kit Best money I have spent on my trailer!
  13. Replies
    8
    Views
    190

    Merry Christmas! :santa:

    Merry Christmas! :santa:
  14. Thread: PDP problem?

    by Danrude
    Replies
    22
    Views
    661

    :thumb up2:

    :thumb up2:
  15. Thread: Trim switch

    by Danrude
    Replies
    21
    Views
    570

    :thumb up2: Thanks for the update.

    :thumb up2: Thanks for the update.
  16. Thread: Trim switch

    by Danrude
    Replies
    21
    Views
    570

    It sounds like that the PDP is the problem, most...

    It sounds like that the PDP is the problem, most likely a cold solder joint!
  17. Thread: Trim switch

    by Danrude
    Replies
    21
    Views
    570

    The blue wire is trim up and the green wire is...

    The blue wire is trim up and the green wire is trim down!
  18. Thread: Trim switch

    by Danrude
    Replies
    21
    Views
    570

    The ground is from the base of the tilt trim...

    The ground is from the base of the tilt trim motor and I believe there is a ground strap connected to the motor or near by. My guess is that you have a bad or loose connection. You can measure 12v...
  19. Replies
    38
    Views
    1,063

    Sorry for your loss, prayers for both of you!

    Sorry for your loss, prayers for both of you!
  20. The push on connectors are molded on the wires...

    The push on connectors are molded on the wires for the key switch, years of flexing at the connector will cause the wires to break inside the insulator. Check those out before you spend money on a...
  21. Thread: PDP problem?

    by Danrude
    Replies
    22
    Views
    661

    It's been over 12 years since I have worked one...

    It's been over 12 years since I have worked one and cain't remember exactly how I removed it. You may have to do as you mentioned and remove the screws from the bracket so you can access the back of...
  22. Thread: PDP problem?

    by Danrude
    Replies
    22
    Views
    661

    It sounds more like a key switch issue to me, the...

    It sounds more like a key switch issue to me, the system check cycling after you release the key from the start position tell me you lost power in the start position. it could also be a problem with...
  23. Thread: seat removal

    by Danrude
    Replies
    3
    Views
    138

    There is a padded center piece that wraps over...

    There is a padded center piece that wraps over the top of the back rest, look closely at the two sides of that piece for a small hole on each side of it. a phillips screw driver will pass through...
  24. It sounds like you have a leak at the filter, it...

    It sounds like you have a leak at the filter, it is easy to get them cross threaded.
  25. Replies
    5
    Views
    182

    Trailer wheels ore 5 on 4.5 with 0 offset.

    Trailer wheels ore 5 on 4.5 with 0 offset.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4