Thank you JOE54. I've ordered all parts associated with this issue through European Marine. I appreciate the help. I did print all pages that will help in removal, cleaning and replacement of parts....
Type: Posts; User: BillDSR
Thank you JOE54. I've ordered all parts associated with this issue through European Marine. I appreciate the help. I did print all pages that will help in removal, cleaning and replacement of parts....
During a tournament on Eufaula, 1992 Mercury 175 HP XRI quit running, SN 0D167948. Removed engine cowl and found that there was a fuel leak. Primer bulb would not stay primed, went weak shortly after...
US Army 1980-1986, UH-1H helicopter mechanic and crewchief. Oklahoma Army National Guard 1986-2019, UH-1H, OH-58. CH-47, UH-60 and UH-72 Lakota mechanic, crewchief, flight engineer and technical...
As a professional co-angler, kinda, it's my go to bait. With that said, I've caught every species of fish known to man with it during tournaments, part of the heartache with it. My PB came on a Ned...
Buzsaw, did you remove the carpet prior to drilling with the hole saw? Curious as to just how you were able to reach in the locker to cut the hole. Going to do this to mine, any advice you could give...
Interested in this also. Keep us informed.
I changed my AGM's to Relions (https://relionbattery.com/products/lithium/rb40) 2 years ago. They saved me approx 128 pounds of weight and last two days of my type of fishing. Never an issue full day...
I had an issue with one of my pumps. Decided while I went to all the trouble of changing one out, I replaced everything! One more thing I thought of...if the people that replaced your valves DID NOT...
I have the same system as yours. With the levers for each livewell set at "empty", the livewells should drain out the back drain ports. With the levers set at "fill", there should be no drain from...
I run a 24P Trophy and a 23P Tempest Plus. I've had the Tempest balanced and blueprinted also. Usually keep the Trophy on, and Tempest as my backup.
Read your question in "Bass boat setup".
Replied: I have a Merc 175 so there might be a difference in gear ratio, not sure. However, with tournament load, half tanks of gas and two onboard, ...
I have a Merc 175 so there might be a difference in gear ratio, not sure. However, with tournament load, half tanks of gas and two onboard, mine ran right at 62.4mph at 5650rpm. That was with a...
We have a winner! :thumb up2:
Than you.
Will do.
1. Yes, I downloaded to the computer, then ran it to transfer the file to the update card. I used two SD cards, one for each unit. Each card has the transfer update and installed in both the 8610 and...
I downloaded the newest update to an SD card, and followed directions for install. 8610 would not bring up the update in slot #1, but would bring up the update in slot#2. When I updated the 942,...
LWINCHESTER2, apologies for the delay, I was at Sam Rayburn fishing as a co. I did as you advised and it seemed to work. However, I did this while the boat was on trailer, but the ClearVu down did...
I'll give this a try this morning and get back with you. Thank you, Bill
I recently installed an 8610xsv at the console. I have current updates, and the GT30+GT15 IH as my transducers. They are individually plugged into their respected ports, 8 pin and 12 pin. The issue...
I ran 10 gauge marine grade wire from the battery directly to a fuse block that I mounted under the console. From there, I ran 12 gauge to the bow for the graph. Use appropriate fuse at the block,...
Try Ranger parts. I bought my boat two years ago, and ordered one from them. They had one built and sent to me in a couple weeks. Carpet color didn't match perfectly to what was in the boat, but...
LWINCHESTER2, I followed your advice and found that with the Y cable installed, there was no option for GT30+GT15 in the transducer selection. I then installed each transducer to its respective port,...
Thank you sir, I will give this a shot tomorrow after work. I appreciate the guidance LWINCHESTER2.
I have a 7608xvs mounted on the console and the GT30/GT15 combination with Y chord installed. GT30 is mounted on the jack plate, GT15 in hull. Graph was updated last Tuesday prior leaving for a...