Search:

I just went through this today and NOT waiting long enough ended up being my problem…

I just went thru this with mine… If your Ultrex has a built in transducer check the barrel connection in the head (located near the fuse) and make sure it’s tight. I was getting interference turning...

I’m posting this in hopes it my help someone in the future…

I recently decided to modify my M360, Helix 12, Helix 9 and Ultrex with built-in MDI setup by adding a heading heading sensor and “Y”...

Thanks guys, I think I’ll give the Y-cable a try and see how it goes.

Just playing around in the garage it seems like turning on the Ethernet hub first and then adding units one at a time may help...

Ok, I have two Helix units at the bow, a 9” and 12”, both are Mega DI+ G3N. When I originally installed them I did not use a “Y” cable, the M360 is hooked to the 12” and my Ultrex with built in Mega...

Thanks to everyone for their response!

I think that is what I’m going to try and do, leave AS GR50 GPS on the the stern near the SI transducer and locate the AS GPS HS upfront near my bow units. I’m assuming I can subscribe to the module...

They are all Helix units so I’ll put it up front. Thanks Wayne

I currently have an older AS GR50 GPS module on the stern which is on the network and will be adding an AS GPS HS so I can mark and see waypoints on my M360. My question is, is there any value in...

:thumb up2: Thank you!

Does anyone have the state of charge numbers for the group 31 X2? Seems like I’ve run across them on here but I haven’t been able to find it.

Just for reference, I have a 52” on a Nitro Z-7 that I currently have set 6” higher than the lowest setting. We have a lot of wake boats here on our local lake and it’ll occasionally pop out of the...

:thumb up2: Thank you

Mine was a loose spade connector on the switch. Common problem...

Thanks Wayne, I have an older AS GR50 GPS module on the stern which is on the network, but I would assume I probably need to or would at least want to put a new AS GPS HS at the bow close to the 360...

Thanks, I’m not surprised since I couldn’t find anything on it. I do have m360 I’m planning to set that up that way. I think I need to pick up a puck for it if I remember correctly.

Is it possible to display waypoints on side imaging? I’ve tried to find information on this and haven’t come up with anything.

The day I was having all of the issues I finally disconnected the unit with the m360 from the Ethernet and everything was good. I’m not using a Y cable, my 12”Helix is hooked directly and then shared...

I’m convinced this issue is related to the Ethernet and how the units are setup to share information. At one point I was about ready to abandon the 5-port Ethernet box try sharing via cable between...

How are the Minn Kota Precision chargers working out with the different lithium’s? Seems like I’ve read where in some cases they show a different state of charge than the battery’s BMS, but in the...

A while back I posted with the same problem.

http://www.bbcboards.net/showthread.php?t=1065776&highlight=

Cooker do you have your units networked together? At the time I was having issues I...

I’ve done short trips with limited hyway travel without a problem. Anything longer I have a bungee over each of them.

There’s been a couple threads on it recently, here’s a couple links....

http://www.bbcboards.net/showthread.php?t=1070892

http://www.bbcboards.net/showthread.php?t=1074068

Thanks for the tip, I just went out and changed mine. It’ll be interesting to see what it looks like the next time I get out.

I’ve run a dual pro professional for the last six years that way, with 1-agm and 2-lead acids. My PM1 agm lasted five years and my two lead acids are going on six years. If I remember correctly, I...