I may have linked the wrong one, but there were some on there that were in the 100 psi range, and liquid filled. I just didn't know if air going to a fuel gauge would mess it up. Unfortunately I...
Type: Posts; User: prc4816
I may have linked the wrong one, but there were some on there that were in the 100 psi range, and liquid filled. I just didn't know if air going to a fuel gauge would mess it up. Unfortunately I...
So, I'm not trying to promote them, more using them as an example, but would 2 of these with a hose going to the appropriate valves work?
...
I don't know the pressures, I don't have access to gauges. I don't know about the bulb, because I'm not talking about a complete loss of power, more like a hesitation or a stutter. When this...
I have 06 Optimax 200 serial number 1B256164. I recently replaced the LP fuel pump, and while I had the VST apart, I inspected the needle and float, and cleaned the passageway with carb cleaner. When...
I know this thread is a little old, but has anyone had any experience with these, or any other aftermarket pumps?
If you get a chance to find it, I would greatly appreciate it
Is there a way to do the sweep test with a volt ohm meter?
I recently took my triton to the mechanic for an issue I was having where when I went to take off the motor would not accelerate (RPM's remain at idle). Let it sit for a while and it ended up taking...
I'm not the one that preformed the original test. I figure I will contact the seller and see if he will allow me to conduct a new compression test to the specs listed above. It's been a while since...
That's what I was thinking. Thank you.
I am looking at a used 2005 Optimax 1B072210. Motor has 218 hrs on it, with all but about 20 hrs below 4.5k rpm. Most hours are under 4k rpm. The seller states compression reads 80-85 psi. Is this...
Will do, thanks!
I actually called them, but they said that they didn't have any used motors. I've been trying to check C&O regularly, they look like they have a pretty good supply of used motors. I'm looking to...
I don't know if this is the right place for this or not. I am looking for a used 200 optimax, and would like to find a boat shop that deals in used motors, that would possibly take mine on trade, or...
Got ya. Again, thanks for the quick replies, and patience with me. I will recheck compression this weekend, and hopefully they will improve. The other thought/question I had today was, what kind...
I will retest following these guidelines, which will hopefully improve the numbers. When you mention holding the throttle plate at WOT, would engaging the hotfoot be sufficient? The battery is kept...
So, I have some updated information, but to answer your questions first, I have not checked fuel pressure. The bulb does pump firm, I actually checked that initially, but it feels just like it...
I have recently started using straight shank flipping hooks and snell knots for my creature baits, and the hook up ratio is significantly better. In the dead of summer I fish 10+in worms...
Not much to update on. Took the fuel filter off, and found a seal that got sucked down into the filter. Thought this might be causing a fuel restriction, but made no difference. Is there a...
VR's seem to make sense to me. I will try and pick up a manual. I've got access to to volt/ohm meter and someone who is pretty good with it. Thanks for the help Don.
Thanks, I was just curious. Also is there any test for voltage regulators? I have been keeping my eye on them for a while, but the terminals/wires/regulators look ok. I had a bad cranking battery a...
Just out of curiosity, what all does a readout show?
I have a 200 EFI ser# OT148526. On an outing about a month ago, it took off from the ramp like normal, and ran fine. Later that afternoon it started not wanting to come up on plane, and would only...
Fished the past 2 days on LC. Didn't get a water temp reading, but the water level is at full summer pool of 723ft. Day one included fishing a back creek arm with square bill cranks and...
+1