Search:

How is your hole shot with your four blade prop. 24 pitch

I have a mercury 175 pro xs 2 stroke on a Z18 nitro i was wondering if anyone was running a 4 blade prop and if so what pitch mine has a 3 blade 24 pitch fury. Was wondering if i need to drop to a 22...

My last engine before i bought my 2016 Z18 175 pro
xs was a Yamaha so like you i had to get used to all the different noise of the Mercury 1, The slow spin of the engine on startup sounds like a...

The heading sensor is not supposed to be mounted on metal that would cause magnetic interference they tell you only use stainless screws that a magnet won't pick up if you are replacing the ones that...

Sorry didn't think i needed it for vessel view mobile. I called Mercury the other day talked to Adam nice guy we went through everything deleted the app and reset it up everything worked after we did...

Fox i called Mercury yesterday and talked to Adam we got my VVM working correct. It wasn't reading the codes but was displaying that it had a fault, Now it gives more detail like i made a fault and...

I installed my vessel view mobile and everything works but the fault codes won't display today i had a wire come loose and caused a code but it will not display the codes and check the internet...

Yes oem thermostats, I though about ordering a set of the cheap ones to see how they done. Will the 130 F thermostats from the older models work on my engine? Well water temp is in the 90F right...

Hi Guys #2b121983 175 Pro XS 2016 I am new to Mercury the new model engines. I am not getting any alarms the last two times out. This is what i have done, both thermostats replaced. Poppet removed...

It does show water pressure on my 2016 175 Pro XS

Thanks Guys for all the info I have went thru the water pump, the poppet valve, install new thermostats, flushed the system. I did find a gasket under the water pump had a place in it missing don't ...

Mine is newer 2016 looking at back of engine right side toward the front where the cowl makes the turn. The yellow cap is a resistor that plugs into the harness. On my instruction it said you may...

# 2B121983 Sorry for all the questions but trying to figure out this running hot problem. Will a poppet valve stuck closed cause a hot condition. Normal temp running down river is about 115F this...

Had engine checked this morning had overheating code in both banks which showed like 186F when coded i bought gaskets and seals for thermostats, poppet valve and water pump don't think it is water...

2016 sorry forgot

Talked to Mercury today they said thermostats were not covered they were normal wear items. Going tomorrow to have codes checked at the dealer. Has anyone used other brands of thermostats it appears...

Hi Guys Does anyone know what codes 236 and 21 on 175 Pro XS 2016 Mercury #2b121983 This is the code on my Vessel View Mobile Don't know if they are actual codes or not This is in my fault on the...

Hi Guys I have a 175 Pro XS #2B121983 Bought this boat a month or so ago engine had 59 hours on it when i got it have 68 hrs now still under warranty I have had an alarm to go off 3 or 4 times on...

I found the compressor strainer I removed it and it had grass all over it was worth the time to clean the strainer. Next will be the thermostats !!

Joe would you know the torque for the divider plate. Cub48

2016 Mercury 175 Pro XS # 2b121983 I was looking for the compressor strainer yesterday and noticed a bolt missing on the plate that the coils bolt on in between the two heads this is a plate that is...

#2B121983 2016 175 Pro XS I was looking at different forums and saw the one cleaning the compressor strainer so i was looking at mine it was different than the one that was in the picture. Does this...

I have mine set at 3 1/2" seems to be good .

Hi guys Serial #2B121983 Mercury 175 Pro XS 2016 year 60 hours on engine still has 6 months warranty left, had boat about 1 month New to Mercury last boat motor was Yamaha, Prop 24 fury no plugs in....

Do you have a jack and if so do you know your prop to pad? I just bought this boat and put a 6" jack plate on it and was wanting a starting point right now i have it at 3 3/4" had it at 3 1/4" but...