On reassembly does it require the use of the piston rod alignment tool. How will this motor compare to the 200gt I currently have in hp & fuel consumption.
Any ideas as of why the bottom cylinders...
Type: Posts; User: Bass Fisherman
On reassembly does it require the use of the piston rod alignment tool. How will this motor compare to the 200gt I currently have in hp & fuel consumption.
Any ideas as of why the bottom cylinders...
Hey guys, I have bought an Evinrude & I have few questions. I gave very little & it is a great looking motor.
Model no. E175FPLSDS Serial no. 05114522. It has low compression on bottom cylinder on...
Yes I will follow everything just like they say. I have placed my order, they are out til first of year. I hope all goes good I just want fish.
Thanks for the help & advice
Thank you guys I have decided to go with the SEI I found them for around 895$.
thank you for everyone’s response.
Yes sir I agree. I have a ton of money in rebuilding the power head this summer. I have been looking at them from what I see they run about 1000$. Can u tell me which one I would need I see couple...
Thank you you’ve been a great help
Ok great then maybe it will be ok.
Thanks for the help fellas
All that is listed is it came off an Evinrude 200. It said a 1993 200XP but did they make the XP IN 93? The shaft measurements are real close to mine maybe a little bit shorter sorry that is all I...
The seals failed and case leaked water, under inspection I found a tooth missing from forward gear so I decided to replace everything. The case seemed to be ok never hit anything other than slowly...
One last thing fellas, so last summer I put new gears & some new bearings in this LU & I did not have the shaft shimmed properly I just put back what I took out as far as shim material. Took her out...
Thank you. So if I find one but has wrong size shafts is it as simple as putting my shafts on it. Also do you know what year they started the 2 piece shaft
Ok u do mean change the upper half of driveshaft. My lower is shot. If so can this be done without removing from lower housing.
Thanks
I’m not sure either maybe someone here can tell us. Do u have it off? If so could u send some pics to me. 859-585-0685
Hey guys, I am in need of a lower unit for 1993 Johnson 200 20in shaft standard rotation. If anyone has anything please let know
Thanks.
Ok thanks
Hi guys, can someone please tell me what hub kit I need to put a Raker 2 prop onto a 1992 Yamaha 200 15 spline shaft
Guys can someone tell me what hub kit I need to get a Raker 2 prop to fit on a 1992 Yamaha 200. 15 spline
I did not change the shaft. I did put a new set of gears & pinion gear in it. From what I read I was under the understanding that it had to be reshimmed. I was getting some very fine particles of...
No large chunks, real fine mushy junk.
Great thank you.
The reason why am asking about a shim gauge is because when I rebuilt the engine I also rebuilt the LU. New bearings, gears & seals. I did not know until later u need to check the shaft. The issue I...
Hey guys can someone please tell me what the part no is for a driveshaft shim gauge.
Engine 1993 Johnson GT 200 standard gear case.
Hey guys can someone tell me the part no for the driveshaft shim gauge for my engine. Engine is 1993 Johnson GT 200 I think it’s a standard gear case
Thanks. I thought I had herd his name thrown around here.
Hey guys, I got a 24p raker2 over weekend & I an disappointed with its performance. It is in excellent shape after plugging up 2 of the 3 holes this thing would not get a good bite on take off & top...
Thanks fellas yes I’m happy for now🤔 wish had went with a 24p but this will do until I can try before I buy next time.
I do not want to get close to rev limit. It’s been long road here hate start...