Recently been experiencing an issue with my 1998 Mercury 200EFI. Motor will start fine in the morning and run fine but it seems that once the sun gets up and starts beating on the cowl that I start...
Type: Posts; User: IlliniMatt21
Recently been experiencing an issue with my 1998 Mercury 200EFI. Motor will start fine in the morning and run fine but it seems that once the sun gets up and starts beating on the cowl that I start...
D&S Marine in Roscoe, IL is where you want to go. They repaired my 391V after it was rear ended - rebuilt the entire transom and resprayed the gel to match just about perfectly. They also refinished...
I know it's a long shot but looking for a set of carbs for my pontoon boat - 2001 Mercury 90HP 4-stroke. 804168T1, 804168T2 and 804168T4.
You'll need to get at it from behind to remove the hose that goes to the gas tank which is most likely being held on by a hose clamp. Not familiar with your model but for my 391V I had to pull the...
Have you tried calling Shelby Industries? They were very helpful when the handle on mine broke and I needed a replacement. Sent it out to me for almost nothing IIRC.
I had the handle break on the Shelby trailer jack on my '91 391V and was able to call Shelby Industries and they sent me a brand new one for practically nothing. The guy on the phone was extremely...
I love everything that you did. You can tell your workmanship is impeccable, even through the pictures. I would love to do the same you did with the factory deck extension - any chance you have...
+1
D&S is the absolute best around. You will thank yourself for making the drive up there. I won't take my boat anywhere else.
Agreed. Trying to do my 391V and running into the same issue with the insert that holds the edges of the old carpet in.
Any opinions on the SeaStar (Teleflex) blinker trim control switch versus the unit from T-H Marine?
The SeaStar one seems to rotate with the steering wheel while the T-H Marine remains fixed. I...
I fished out of the exact same boat in college. They are a nightmare to work on but it got me on the water so I loved it. They are definitely unique and pretty fun to drive around but be prepared to...
1991 Ranger 391V dual axle trailer with a 6" jack plate. Just like above, 25' and change from tip of the tongue to the back of the motor with the motor trimmed all the way down.
Keep trying Ranger. They got me exact flake matches for my '91 391V and you cannot tell the differences between the old and new. They just need your serial number.
Dobyns Savvy (Sierra now) 703SF. One of my absolute favorite rods and priced well, too. I also use it for Senkos (wacky and Texas) and enjoy it just as much for those techniques.
D&S Marine rebuilt my transom after my boat was rear-ended. Bob and Jeff are great guys and are very easy to deal with. Their work is top notch and they will make sure you are 100% satisfied before...
Taking a little vacation to Holland this upcoming weekend. Thinking about bringing the boat along and doing some fishing but I'm not very familiar with the area. It doesn't seem like Macatawa is all...
What did you do with the backside of the rivet that's stuck between the top of the lid and the inner fiberglass liner? It gets sandwiched in there with the carpet.
I am working on recarpeting the lids on my '91 391V. Those of you that have done this on your 300 series Ranger, what did you do about the old rivets? I have mine drilled out but because of the inner...
We did that on my school's old I/O Ranger. It's actually a lot easier than you'd think. I'll see if I can find some pictures.
Thank you to Al for hooking me up with his old one! Guys like you are why I spend hours and hours and hours on here everyday! :beers:
Perfect! Thanks guy! Just didn't want to start and end up stuck because something wasn't right. :thumb up2:
Welcome! Sweet ride! Looks like you and I are from roughly the same area - hope to see you out sometime!
Does anyone have a picture of a 1998 200 EFI (or similar) with Sea Star hydraulic steering installed?
I am gearing up to install mine this week and I noticed that my tilt tube is only exposed on...
Does anyone have any tips where I can locate a new steering wheel hub? I am upgrading my 391V to hydraulic steering and cannot get the old hub off the old cable set up. I had two screws strip when I...
I bought all my stuff from Flow-Rite. They have everything you need for your livewells. It may be worth it to replace your valves while you're down there since they probably not far behind your hoses...