Thank you Don!
Fyi- I have changed the plugs with exact replacements per your comment below (properly gapped) and did a compression test (all good and very close) since the skip started getting...
Type: Posts; User: FishinMcNut
Thank you Don!
Fyi- I have changed the plugs with exact replacements per your comment below (properly gapped) and did a compression test (all good and very close) since the skip started getting...
Us saltwater guys replace all of the engine anodes at least every other year. You should have one on your swivel bracket, a small pair just above the cavitation plate and the flush pancake one under...
Don, My 250 racing Opti (1E000861) has always seemed to have an occassional low speed in-gear miss since zero hours but always ran strong and smooth. Now at 400 hours the miss seems to be getting...
Great call as usual Don. It was the yellow wire to the MAP sensor. It was chaffed and grounding against the block.
Appreciate your experienced insight!
Don, nothing is "off the wall". I very much appreciated the way you approach issues. That's why I asked!
Thanks for providing a starting point to begin trouble shooting. I'll check the stuff I...
Don- I'd like to tap into your vast experience. My Optimax 250XS suffered a MAP sensor failure at 102 hours. It ruined a multi day fishing trip. Dealer replaced it under warranty and did the 100 hour...
The warranty on my 250 XS expires 8/2011. By 9/2011 it will be sporting some added Hydro Tec muscle.
I had their phase kit on my last motor (Yammi) and reall liked the result and the experience...
I did the Phase ll on my 175 HPDI and was very happy with the results.
Sweet! Been anxious to see this beast
Can you throw up a side-by-side shot with a stock Merc tuner to show the contrast???
I'm game as soon as my warranty expires. I saw first hand what you...
I'm wondering if he has the harness in place that runs between the fuel sending unit and the motor?
I watch my temp gauge on every start up. It goes up to 150 and then drops to 120 when the stats open. Only after seeing this complete is will I give it throttle.
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Shotgun »</TD></TR><TR><TD CLASS="quote">Mine does it between 3-4000, thats the motor saying...
It should have come with a cling on decal with detailed break-in instructions.
I went through this in November. My 250XS break-in was 122 minutes. I recall the instructions said to vary RPM every...
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Hardhead1 »</TD></TR><TR><TD CLASS="quote">nice job. looks like the drill bit got away from you a...
I finally got around to installing the LU plugs I bought from Don. It is a very easy DIY that sounds more complicated than it actually is. The biggest challenge was finding a 1/16" NPT tap. Once it...
I made the same engine switch a month ago.
All of my livewell pumps, electronics, VHF radio, and more are wired to my crank battery. At the time of swapping motors I installed a new Odyssey 1700...
Help...
I've searcedh all over looking for said instructions. Where can I find them???
Was thinking about tapping the top 3 holes and installing short allen head screws with Locktite...
Phase 2 on a 175 HPDI. Hangs on an 18.9 Egret carbon/Kevlar flats boat down in Florida. Nathan was a huge help in getting me set up.
Numbers: 59.7 with heavy load (three peeps, 40 gal livewell,...
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by STROKEDYAMAHA »</TD></TR><TR><TD CLASS="quote">Nathan says 89-91 </TD></TR></TABLE>
Nathan had...
I can attest that Nathan will steer you right. No BS from him at all http://xs-s.com/zf/images/smile/emthup.gif
Edit:
Miker, I put the Phase 2 on my 2.6 HPDI a few months ago. Increase was 500...
If it were me... I would call Hydro Tec and discuss my options. They are honest and truthful in suggesting mods. Give it a try.
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 21XDC »</TD></TR><TR><TD CLASS="quote">They are the bomb! They have spent some time with me on...
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by James O. »</TD></TR><TR><TD CLASS="quote">Ive been using Mobil 1 for 4 yrs with no problems. ...
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by stan »</TD></TR><TR><TD CLASS="quote">If he is burning at 10 to 1 ratio I dont think the oil...