Search:

Type: Posts; User: BigBucketMouth33

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    456

    Just for notice, they reported they drained the...

    Just for notice, they reported they drained the lower unit oil prior to the pressure test. Not sure if they did any soapy water around anything. We didn't discuss that. Thanks again.
  2. Replies
    5
    Views
    456

    First off, thanks for the input. Don, that is...

    First off, thanks for the input. Don, that is funny you should say that. I wondered myself why so much pressure? To me, even 3-4psi would reveal any leaking components when properly checking...
  3. Replies
    5
    Views
    456

    Wouldn't you see a pressure drop during pressure...

    Wouldn't you see a pressure drop during pressure test if that were leaking? According to tech at dealer, he went ahead and replaced the seals around the while pump when he had it down. Crazy little...
  4. Replies
    5
    Views
    456

    Lower unit oil from water intake

    Serial# 2B590145

    4 Stroke Pro XS 250 sometimes leaks lower unit oil from water intake.

    I changed the water pump awhile back and when the motor was trimmed up lower unit oil trickled from water...
  5. Replies
    12
    Views
    815

    I run a megaware keel guard on my 721. Put it...

    I run a megaware keel guard on my 721. Put it right below bottom wing and its been there for 2+ years with no issues at all. Have beached on cement ramps, sand, and in mud. Installed myself per...
  6. Replies
    11
    Views
    480

    Was unaware of Vessel View mobile not reading...

    Was unaware of Vessel View mobile not reading historical codes. If the alarm is stored in the ECU why would it not show up on VVM?
  7. Replies
    11
    Views
    480

    I did happen to pass thru some hydrilla at one...

    I did happen to pass thru some hydrilla at one point coming out of a cove, but for the most part all clean water. I'm not going to rule out come grass could have been picked up. I just pulled the...
  8. Replies
    11
    Views
    480

    Appreciate the info. Will have the alarm properly...

    Appreciate the info. Will have the alarm properly read to determine the issue. I have MPP until July 2024 if I remember correctly. Thanks for the help and I hope it isn't anything major. Hopefully,...
  9. Replies
    11
    Views
    480

    Question about Alarm During Idle

    Serial # 2B590145

    This weekend at the lake I encountered an alarm that I have never had. My boat ran fabulous, no problems at all. I hit top end RPMs, normal water pressure, and everything was...
  10. Replies
    5
    Views
    602

    Replacing Bow Shroud

    Just received a new bow shroud from Phoenix and plan to install it soon. Has anyone replaced theirs recently? If so, which route did you take? I know it will be basically impossible to drill holes in...
  11. Replies
    4
    Views
    326

    Thanks, fellas. I am going to troubleshoot and...

    Thanks, fellas. I am going to troubleshoot and pull it tomorrow.
  12. Replies
    4
    Views
    326

    Atlas relay harness 2019 721

    Assuming the relay harness for atlas jackplate is mounted under the back deck by the transom on the starboard side? My jackplate quit goin up this weekend and Im assuming relay or switch without any...
  13. UPDATE: After extensive troubleshooting...

    UPDATE:

    After extensive troubleshooting yesterday I found the culprit. A faulty rocker switch caused extensive voltage drop to the 360. I was getting 12.7 volts at switch, but leaving the switch i...
  14. Thanks, Data for reply. That's the problem I am...

    Thanks, Data for reply. That's the problem I am encountering. My sonar tab is not displaying any transducers to choose. I just downloaded the new software to SD card. Will install on unit shortly and...
  15. Mega 360 Transducer Not Connecting to Helix 12 DI G4N

    Recently, I received my 360. Wired it up with a Y cable so I could utilize my MEGA DI on trolling motor if need be. With everything hooked up, my Helix 12 will not even power up. I simply unhooked...
  16. Replies
    3
    Views
    369

    Thanks for the help. Yes, I agree. Seems like...

    Thanks for the help. Yes, I agree. Seems like tasks that are thought to be simple, always turn into a "BIG" job lol.
  17. Replies
    3
    Views
    369

    7 Pin Trailer Wire Replacement

    I thought I saw a post on here awhile back about the cord replacement for the boat trailers. Mine is getting a good bit of wear and I would like to replace it. Anyone have a link to the cable that...
  18. Replies
    7
    Views
    500

    Good info. I figured it would be way better, but...

    Good info. I figured it would be way better, but just wanted to hear some feedback. Thanks
  19. Replies
    7
    Views
    500

    Switch for Mega 360

    I just ordered a mega 360 and was curious how many of ya'll are running a switch for the transducer? I read somewhere that humminbird recommends adding a switch during the install. I have the switch...
  20. I just bought one last night 10/27 from Bass Pro...

    I just bought one last night 10/27 from Bass Pro as well. The day before that I checked and they were "out of stock"
  21. Replies
    4
    Views
    399

    Just curious to know why it randomly tried to...

    Just curious to know why it randomly tried to detect it when all this time it has been reading perfectly fine from the XTM MDI trandsducer on my trolling motor. Are there any particular reasons as to...
  22. Replies
    4
    Views
    399

    Helix 12 G4N 360 No Image

    Yesterday while on the lake my graph went stupid. I bought and installed a couple months ago. Everything has been great with it until yesterday it started acting like it was reading from a Mega 360....
  23. Replies
    7
    Views
    515

    Thanks for the help. I actually was able to lay...

    Thanks for the help. I actually was able to lay under the trailer and verified that XP100W0301 is printed on it. I never noticed it before. Thanks for the help and info. Now, I will begin looking for...
  24. Replies
    11
    Views
    914

    I installed a KeelShield as per the instructions...

    I installed a KeelShield as per the instructions that came with it and I am highly satisfied with it. Over 2 years on the install and all is well. I put my below the 3rd bow wing and it works as...
  25. Replies
    7
    Views
    515

    Fulton Jack for 721 Trailer

    Does anyone have a lead on the model Fulton jack on the trailer for a 2019 721. Obviously, its a marine master trailer and I have a fulton jack on it. I need to replace jack and want to make sure I...
Results 1 to 25 of 190
Page 1 of 8 1 2 3 4