Good grief. So what exactly should I have purchased?
It is A 280 2.5 litre more FYI. BTW.
Type: Posts; User: dondante
Good grief. So what exactly should I have purchased?
It is A 280 2.5 litre more FYI. BTW.
Ok I took it back and purchased a Optima D31M. I think I'll be good to go. :)
Thanks for the help, guys.
I run 2 Helix 9s and sometimes my stereo. Motor is a 2000 Merc racing 280 Offshore. (alternator)
I just picked up an AGM from Advanced Auto Parts. To replace an old group 27 start batt8)
They...
I went to stow my ulterra today and it came up but the motor stayed vertical. So it didn't exactly stow properly. I did the power button 3 times procedure. It did the same thing. Came straight up but...
New Helix 9 mega chirp GPS.
Whenever I turn the unit on it goes to the screenshot page.
Is that normal? My 9 Mega SI goes to lastscreen selected when turned off of I remember correctly.
My Bow panel is slowly wasting away. :(
Who is making replacements?
Who has installed an Ulterra on an Allison xb03?
I've got that and a mk-A21 and a MKA-51bracket. I don't think it's going to work.
Who has installed an Ulterra on an Allison xb03?
I've got that and a mk-A21 and a MkA-51 bracket. I don't think it's going to work.
How hard was it to remove the old bushings? :eek:
I purchased a Hydraulic seat pedestal from BPS but it is sort of loose in the hole. It can be moved side to side with a bit of play. Not snug at all.
Any ideas?
Its a screw-in pedestal. No...
I purchased a Hydraulic seat pedestal from BPS but it is sort of loose in the hole. It can be moved side to side with a bit of play. Not snug at all.
Any ideas?
Its a screw-in pedestal. No...
Who's got experience with a Trophy on an xb2003?
I have a 2000 03 with a 280 and currently running a 28 ET. I'm looking for handling more than every ounce of top end speed I can get.
Most of...
Yes. That's the one. It cleaned up well. New carpet clean 280. Put new decals on motor.
I purchased that boat. :D
Got any pics of that rod rack you made?
Do I need to reverse the brackets to install? I have the hydraulic against the transom and the spacer brackets to the motor.
J, I JUST tried a 26 trophy and have PSI for days and crazy bow lift. Half loaded 5800 rpm's it solved the problem for sure. Getting 15-20 lbs of pressure now. Now I can play with the plate. I'm...
And I also stated that with another person it won't get on the pad and the ass is high aka 10# or lower psi. That's my real problem.
Thanks for all the input, guys. I'll report back tmrw.
My problem is when I have someone in the boat and can't get on the pad. Not by myself which is numbers I gave. I will know tmrw when I run it again after dropping the plate.
I plugged top ³ holes already.
Around 6100 rpm. Can't even begin to get it on the pad with a person onboard. The ass is high and I get below 10# of water pressure.
Can someone tell me about where to start on height? I can barely if at all get it on the pad at wot only. But most of the time its like the ass is too high. I lose water pressure (5-8lbs) unless it...
K. Thanks for the info. My rev limiter is over 6400. The prop I purchased is used and has some dings to the blades. It needs worked. I'll take it to a prop guy and see what happens after that.
2000 Blazer 190 pro v
1998 Mariner 200efi 2.5
26 Tempest
12" plate
So tried a propout last week and purchased it. I was running 6100 rpm at 75GPS with moderate load AMD 1 person (me...
2000 Blazer 190 pro v
1998 Mariner 200efi 2.5
26 Tempest
12" plate
So tried a propout last week and purchased it. I was running 6100 rpm at 75GPS with moderate load AMD 1 person (me...
2000 Pro-v with a 1998 2000 merc EFI. Anyone have experience with this boat? Prop size recommendations and expected performance? I have 12“ jack plate about 2" below at the moment.
Thanks