All four tires are wearing on the outer edge. I have been running 32psi but have learned they need to be at 50psi. I wouldn't think both axles would be bent, but? I do have to make an extreme turn to...
Type: Posts; User: JAC
All four tires are wearing on the outer edge. I have been running 32psi but have learned they need to be at 50psi. I wouldn't think both axles would be bent, but? I do have to make an extreme turn to...
I have a '93 dual axle Ranger Trail trailer. The outer edge of both left and right tires show excessive wear. Two parts, what is the issue, and how do I fix this. Thanks JAC
I have 215/75 R14 tires on my dual axle on my Ranger trailer. These are trailer tires only. I have always kept about 35psi in the tires. The above discussion about air pressure caught my attention so...
I have a '93 150 EFI Mercury on my Ranger. Living in Iowa it is difficult to find non-ethanol gas so I burn 87 octane gas and always use an additive. This has seemed to work well, so far. I have...
I have a '93 Ranger 482VS that has two live wells and a handle for each of the live wells that say either empty or fill. I have both handles on empty, but notice when I take the boat out of the water...
I have a '93 150 EFI Merc #OD246482. I replaced the starter approx 2 yrs ago and since then the motor has started without any issues. My boat and motor has sat idle for the last two months. When i...
need spark plugs for 1993 150 EFI Merc. #OD246482. thanks.
I think the starting issue might have something to do with the low water pressure. Still wondering what the PSI reading should be for this motor
I have a '93 Merc 150xri serial #OD246482. I usually fish small lakes that require idle speeds and have noticed the PSI on water pressure gauge hovering around 5. I was recently fishing on Table Rock...
I have a "93 dual axle Rangertrail trailer that has grease hubs. I have had this boat and trailer for 10 years and have had hubs go bad 5 times. I am very careful about checking the dust caps for...
THANKS
I have a '93 Merc 150 EFI #OD246482. I would like to change the fluid on the tilt and trim and need to know what kind of fluid to use. Thanks JAC
Coming home from Table Rock I too had a bearing failure. My mechanic had given me a strap with ratchet so I took wheel off and put strap around end of axle and frame of trailer, tightened them up and...
first I've heard of multi-lip seals. Where do I get those. I agree about beer and life.
There is a wear sleeve that goes around spline and is used in conjunction with seal. why is that there, and can a smaller inside circumference seal be used in place of that?
Different hubs. I don't see any grease leaking from either inside or outside. I notice at times the dust caps won't be entirely tight and I will tap them in with a rubber mallet. It has been three...
I have a '93 Dual axle Rangertrail trailer model D4200. I continually have bearing failures due to water leaking into seals. I have this problem since I got the boat and trailer and have replaced 6-8...
The board continually asks me to log in even after I have done so previously, and ask that my user name and password be stored. How come? thanks
Well, I dug deeper and found a seal that was stuck in the drug plug hole. Dug it out with a screwdriver and now new seal fits in perfectly. thanks
I have a "93 Merc 150 EFI, #OD246482. I have just changed my lower unit oil and don't remember if there is a casket for the drain plug nut. Without the casket the nut fits perfectly, with the casket...
Going to try the photobucket way. thanks JAC
Sorry for the delay but BBC doesn't want to take pic. Working on that. In the meantime the control box is square black with a button in middle of handle that puts control in neutral. bottom right and...
Attempting to add pic to BBC board from I phone to computer to BBC board. Won't let me add pic. thanks JAC
Thanks again. Unsure on how to do shift adjustment to make it correct. On a secondary note this motor will not stay at 5000+ rpms. If I let go of the throttle control it will slowly drop to 3800-4000...
I purchased this boat/motor in 2004. The clunk has only appeared in the last 2-3 yrs. There has been water in the lower unit on two occasions. The seals have been repaired by an authorized Mercury...