Search:

Type: Posts; User: ko4nrbs

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    257

    Under Edit Data Boxes and Edit Navigation Boxes...

    Under Edit Data Boxes and Edit Navigation Boxes the only temp selections I have is Temp (WATER) and TEMP. Changed both Edit Data Boxes and Edit Navigation Boxes to TEMP and it works. Selection...
  2. Replies
    9
    Views
    257

    Yes, I selected Water Temperature. Thanks,...

    Yes, I selected Water Temperature.

    Thanks,
    Bill
  3. Replies
    9
    Views
    257

    Yes. Latest and greatest. Bill

    Yes. Latest and greatest.
    Bill
  4. Replies
    9
    Views
    257

    I double checked it and I have the temperature on...

    I double checked it and I have the temperature on a 2D view that appears correct. Temperature in the Accessories Test is Connected.

    Bill
  5. Replies
    9
    Views
    257

    Transducer is connected. I set the box #4 under...

    Transducer is connected. I set the box #4 under Edit Data Boxes and Edit navigation boxes both to Water Temp. It did show 32 degF in my garage when I first turned it on then it went back to the 3...
  6. Replies
    9
    Views
    257

    Helix 10 Temp Readout

    I use a XM-9-HW-MDI-T transducer with my Helix 10 and can't get a temp readout in the Data Boxes. I set box #4 to readout Water temperature but all I see is 3 little rectangular boxes. What am I...
  7. Replies
    1
    Views
    247

    AS GPS HS Setup Reality Check

    I installed my AS GPS HS on my Helix 10 today and wanted to double check the set up. The manual supplied with the ASA GPS HS must be an older version because the instructions didin't match up with...
  8. Replies
    27
    Views
    1,845

    My update took a bit before it started. Give it...

    My update took a bit before it started. Give it more time.
    Bill
  9. Thread: Ditches??

    by ko4nrbs
    Replies
    6
    Views
    884

    Thanks guys. I'll get a screen shot next time...

    Thanks guys. I'll get a screen shot next time out. I also expected a log to show a bright hard return with an accompanying shadow with maybe some limbs showing.
    Bill
  10. Thread: Ditches??

    by ko4nrbs
    Replies
    6
    Views
    884

    Ditches??

    Are these ditches or logs laying on the bottom? It's in the Tennessee river.


    464739

    Bill
  11. Replies
    2
    Views
    253

    Thank you!! Bill

    Thank you!!
    Bill
  12. Replies
    2
    Views
    253

    Transducer Frequencies

    I have the XM-9-HW-MDI-T transducer with my Helix 10 and also use Mega 360. I've read the manual but still don't fully understand the relationship between the standard frequencies and Chirp. If...
  13. Replies
    4
    Views
    346

    I would rather just set the frequencies back...

    I would rather just set the frequencies back instead of all my settings. I went through the complete manual but didn’t see the default frequencies listed. Where can I find them?

    Thank you,
    Bill
  14. Replies
    4
    Views
    346

    Does the Reset set all the Chirp frequencies back...

    Does the Reset set all the Chirp frequencies back to default?
    Bill
  15. Replies
    4
    Views
    346

    Chirp Configuration

    I have a Helix 10 G4N. What is the general rule for setting the frequency range for 2d, DI, and SI?

    I have the range set to maximum now.

    Bill
  16. Switching from 455khz and back to Mega Chirp

    Out on the water today.

    After switching to 455khz. The brighter return is when I switched to 455khz.
    452623

    Mega Chirp before switching to 455khz
    452624


    Looks like it does switch back...
  17. Replies
    4
    Views
    342

    I haven't been out on the water enough yet to...

    I haven't been out on the water enough yet to see. Going back out tomorrow and will pay close attention.
    Bill
  18. Replies
    4
    Views
    342

    Switching between Mega Chirp and 455khz

    So if switching between Mega Chirp and 455khz eliminates interference with Mega 360 how can we be sure the graph did indeed switch back to Mega Chirp after switching to 455khz? This came up when a...
  19. Replies
    4
    Views
    478

    I hope that is not the case. Bill

    I hope that is not the case.
    Bill
  20. Replies
    4
    Views
    478

    My Mega 360 Interference Fix

    I installed one of these DC motor controllers to power my Minn Kota Edge 70 ft.lb. trolling motor in 2019. Was using a Hummingbird 798 with the TM-HDsi transducer mounted on the trolling motor. ...
  21. Replies
    2
    Views
    439

    The Midsouth Version 3 map I used in Oklahoma...

    The Midsouth Version 3 map I used in Oklahoma worked well in my non HD 798 when I selected the Oologah Lake HD map. Can I expect the same with the Southeast card if I used an older version my 798...
  22. Replies
    2
    Views
    439

    Lakemaster Compatability Question

    What map for the Southeast States (Al, FL, etc.) can I use in my older Hummingbird 798CI SI non HD model graph? I have the new mapping card for my Helix but need one for the 798 on the console for...
  23. Replies
    52
    Views
    2,744

    That didn't work for me. Bill

    That didn't work for me.

    Bill
  24. Replies
    52
    Views
    2,744

    Forgot to mention I set it back to Mega Chirp...

    Forgot to mention I set it back to Mega Chirp after disconnecting the DC motor controller.
  25. Replies
    52
    Views
    2,744

    I will post my findings. In my case the...

    I will post my findings.

    In my case the interference was gone when I changed the Mega 360 frequency to 455 kHz. The DI+ frequency changes made no difference. Selecting only the Mega 360...
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4