Search:

Type: Posts; User: mdtritn21

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    2
    Views
    60

    google boat steering wheels and you'll find them....

    google boat steering wheels and you'll find them. You need to know what diameter, shaft size and the hole pattern on some of them
  2. Replies
    4
    Views
    110

    The hydraulic rams on the trim have a relief...

    The hydraulic rams on the trim have a relief valve that normally keep you from over trimming when running at speed.
  3. Replies
    5
    Views
    98

    You should be alright with the shifter and...

    You should be alright with the shifter and throttle cable with a 6" plate. Steering hoses should have plenty of slack too.
  4. A regular opti max only turns 5750 rpm's and a...

    A regular opti max only turns 5750 rpm's and a pro xs turns 6000.
  5. Replies
    6
    Views
    140

    Shift some weight to the rear passenger...

    Shift some weight to the rear passenger compartment I've even ran with water in the passenger live well to get boat level so it runs with out chine walking and faster.
  6. What boat are you running it on and is the motor...

    What boat are you running it on and is the motor a regular 225 or a pro xs? When it's hot you can loose rpm's and speed. The 24" tempest would gain you 200 rpm's but not any speed.
  7. Replies
    7
    Views
    303

    It's probably been B&B and they do sharpen and...

    It's probably been B&B and they do sharpen and thin the blades when a B&B is done.
  8. Thread: TR21 Shroud

    by mdtritn21
    Replies
    8
    Views
    488

    If your talking about the dash panel and the...

    If your talking about the dash panel and the front panel there is a company that makes them from 3/4" material. I'll see if I can find his name and post it here.
  9. Replies
    6
    Views
    529

    Usually the bravo will be 1-2 mph slower on most...

    Usually the bravo will be 1-2 mph slower on most boats but is better at everything else. You also have to pitch up when changing to a bravo because they are lite on pitch.
  10. Replies
    4
    Views
    88

    Fury 3 to Fury 4 pitch for pitch

    Fury 3 to Fury 4 pitch for pitch
  11. Replies
    1
    Views
    66

    Yes 55 lbs.

    Yes 55 lbs.
  12. Replies
    10
    Views
    99

    Did you get the flo torq hub kit new for it? If...

    Did you get the flo torq hub kit new for it? If you did all the parts shown above should be in the kit and used for installing the prop and you have to use all of them.
  13. Replies
    14
    Views
    351

    I guess it slips on the thrust washer or wobbles...

    I guess it slips on the thrust washer or wobbles on the shaft that's why they made it but they don't have them in the hub kits for other makes of motors so you have to buy them. It takes 100lbs to...
  14. It showing 14% slip which is high for a Gen 2...

    It showing 14% slip which is high for a Gen 2 lower normally it will give slip numbers down closer to 8% and high for a new tempest. He'll pick up 150+ rpm's in cool weather and a few mph but he...
  15. Replies
    7
    Views
    290

    Make sure which ever charger you get is sealed or...

    Make sure which ever charger you get is sealed or the same thing could happen and dual pro won't warranty the charger if it gets wet. Logo doesn't make it worth more or work any better.
  16. Replies
    18
    Views
    744

    2001-2004 TR 20 They were rated for 225 hp.

    2001-2004 TR 20 They were rated for 225 hp.
  17. Replies
    14
    Views
    351

    I've got 4 of them and they all have the coned...

    I've got 4 of them and they all have the coned bushings in them. The instruction you posted says to use it with a hub kit with a forward bushing which torques to 100lbs and that the hub kit (835257...
  18. Replies
    16
    Views
    203

    I wouldn't put a hydraulic jack plate on it...

    I wouldn't put a hydraulic jack plate on it because of the cost and the fact that that boat has wood stringers, a wooden floor and a wooden transom which have all been known to rot. Unless you can...
  19. Replies
    14
    Views
    351

    The hub kit #835257Q6 or K6 for the tempest,...

    The hub kit #835257Q6 or K6 for the tempest, fury, trophy, and bravo props on a Mercury motor with a 1" shaft comes with a coned bushing and is torqed to 100lbs and speed makes no difference. Rkammer...
  20. Replies
    2
    Views
    61

    You need to be running higher prop to pad so...

    You need to be running higher prop to pad so raise the motor one hole up to start with and try it.
  21. Replies
    16
    Views
    203

    Get a six inch manual jack plate it's all you...

    Get a six inch manual jack plate it's all you need.
  22. Replies
    20
    Views
    876

    Get the solid plugs and take the ring off and put...

    Get the solid plugs and take the ring off and put all solid plugs in it and try it since it blowing out now. The plugs should stop the blow out on that regular 225 opti max.
  23. Replies
    16
    Views
    203

    I don't know what IMG 3004 is supposed to be but...

    I don't know what IMG 3004 is supposed to be but it's not prop to pad height. Use this to measure prop to pad http://www.bbcboards.net/showthread.php?t=62660 I think you'll find it's about 4.5"...
  24. Replies
    20
    Views
    876

    Start with all solids that's how I run my trophy...

    Start with all solids that's how I run my trophy props and see if it bogs down or spins up to 3500-4000 rpm's. If it still bows out with all solids you'll need a cav ring on the prop and then try...
  25. Replies
    12
    Views
    318

    If it turns the tempest 5700 in the winter the 25...

    If it turns the tempest 5700 in the winter the 25 fury is too much prop in the summer drop to a 24".
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4