Search:

Type: Posts; User: franktank009

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    67
    Views
    4,210

    Few things to point out, You mentioned 1/4"...

    Few things to point out,

    You mentioned 1/4" hex which is usually sized for a 5/16" socket head cap screw.
    Your torque value referenced is 43 ft lbs which is generally for max clamp load of a 3/8"...
  2. Replies
    67
    Views
    4,210

    Did you buy off a tool truck? Some of those guys...

    Did you buy off a tool truck? Some of those guys are sketchy... If you have proof of purchase from an authorized distributor and your the original owner you should have no problems submitting a...
  3. There's no gasket on the carrier to gearcase...

    There's no gasket on the carrier to gearcase mating surface. It's possible for water to enter the bolt cavity or get into the carrier up to the first oring. It will slowly leak back out of the mating...
  4. The parts diagram posted only shows the upper...

    The parts diagram posted only shows the upper bolt for the carrier. The carrier slides into the lower unit over the prop shaft. But yes the cavity for the bolt is sealed off from oil by the 2 o rings...
  5. The part your arrow points at is the lower unit...

    The part your arrow points at is the lower unit bearing carrier identified in the parts diagram above as part #29. There should be 2 bolts holding it in, one by the skeg and one on the topside of the...
  6. Replies
    40
    Views
    3,360

    this might get real good lol

    this might get real good lol
  7. Replies
    48
    Views
    2,423

    Are those the torx screws for the mounts pivot...

    Are those the torx screws for the mounts pivot bushings? I wouldnt think they would be stainless, I've never seen a black oxide coated stainless fastener before but I could be wrong. A 135 degree...
  8. Replies
    24
    Views
    1,088

    Sounds like a balancing problem. Adding a remote...

    Sounds like a balancing problem. Adding a remote thermostat wont really solve the problem unless you actually install remote dampers for the thermostats to control. Best thing to do is put several...
  9. Replies
    23
    Views
    2,095

    I'm not a big amsoil fanboy but I have to say I...

    I'm not a big amsoil fanboy but I have to say I have been using it for the last few years and I really like the convenience. The selection they have means that I can almost buy all my lubricants from...
  10. Replies
    47
    Views
    2,367

    Drain and fill my transmission and transfer case...

    Drain and fill my transmission and transfer case every year on my f150, 9 years now. I just use a pump and drain through the dipstick hole. Dropped the pan at 100k to change the filter and after...
  11. Replies
    1
    Views
    171

    No, the yamaha hd gearcase lube specifically...

    No, the yamaha hd gearcase lube specifically states on the bottle to only use in the big v6 applications. This is because the lower units on these motors contain no yellow metals. It's a gl5 specced...
  12. Replies
    6
    Views
    1,123

    I believe it was advertised as 25x140

    I believe it was advertised as 25x140
  13. Replies
    14
    Views
    921

    I just use my manual pump oil extractor for...

    I just use my manual pump oil extractor for bleeding brakes. I use a short piece of silicone tubing to slide over the bleeder and the extractor hose. Can be used on any vehicle, also really nice for...
  14. Replies
    2
    Views
    320

    I tried going from a 2inch to 4 inch drop. Didnt...

    I tried going from a 2inch to 4 inch drop. Didnt make a substantial difference. I am strongly considering bolting an f2 winch ontop of the pole step.
  15. Replies
    12
    Views
    469

    Thanks Wayne, very helpful. One more for you. The...

    Thanks Wayne, very helpful. One more for you. The mdi transducer on the ultrex would be compatible with a g1 solix? Does the mdi transducer use humminbirds hw sonar or just the standard dual...
  16. Replies
    12
    Views
    469

    I have a question related to unit sharing. Does a...

    I have a question related to unit sharing. Does a unit have to be displaying the sonar type that you want to share with another unit? For example, I have a solix g3 hooked up to a mega 360 split to...
  17. Replies
    224
    Views
    10,046

    I believe your sick in the head if you actually...

    I believe your sick in the head if you actually think what you said is right. Not everybody is in a situation or state of mind to just leave. When employers take advantage of that it's not the...
  18. Thread: LBF code

    by franktank009
    Replies
    10
    Views
    769

    River2sea is actually on the exclusion list at lbf

    River2sea is actually on the exclusion list at lbf
  19. Replies
    44
    Views
    1,577

    We have a great parental leave program covered by...

    We have a great parental leave program covered by our federal employement insurance. Traditionally 52 weeks, for which 12 weeks are required to be taken by the mother and remainder can be shared...
  20. You'll break the winch trying to pull up a...

    You'll break the winch trying to pull up a caracal. The trailer needs to be kept out of the water so much to get the bow over the roller. So using the winch is a no go and power loading the boat...
  21. I might be expecting too much but the wiring is...

    I might be expecting too much but the wiring is messy, cheap dangling exposed terminal block, wasnt impressed by the crimped terminal ends. I would have expected wiring to be run cleanly and...
  22. You sure proved the point by getting your panties...

    You sure proved the point by getting your panties wound up in a knot lol.
    Glassing the cap on last time I checked is still a form of bonding... and I did say the trailer itself is pretty good, just...
  23. Ha this is so true. I own a basscat and there's...

    Ha this is so true. I own a basscat and there's lots of things that are subpar based on cost... the trailer construction is decent, paint isnt all that great. The bow roller and winch setups are...
  24. Replies
    10
    Views
    415

    The depth of water is not really important,...

    The depth of water is not really important, what's important is the depth your actually jigging your spoon at. If your jigging off the the bottom then great. I do believe the ultrex mdi transducer is...
  25. I fish trails with the same partner and have been...

    I fish trails with the same partner and have been for quite a few years so my answers dont really apply to these club type co angler draw tournaments. I'm blessed to have a fishing partner that is as...
Results 1 to 25 of 256
Page 1 of 11 1 2 3 4