Search:

Type: Posts; User: .44mag

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    52
    Views
    2,985

    It's an adrenaline rush for adrenaline junkies....

    It's an adrenaline rush for adrenaline junkies. IT can become mundane (for a lack of better words) after a while. 26 years.
    Glad no one was hurt.
  2. Replies
    3
    Views
    1,217

    :laugh:

    :laugh:
  3. Replies
    7
    Views
    1,686

    :doh: funny

    :doh: funny
  4. Thread: Old preacher

    by .44mag
    Replies
    8
    Views
    1,572

    :roll::thumb up2::thumb up2:

    :roll::thumb up2::thumb up2:
  5. Thread: Bad Doggy

    by .44mag
    Replies
    6
    Views
    1,700

    Good one

    Good one
  6. Replies
    6
    Views
    1,555

    :roll:

    :roll:
  7. Thread: It's Fall

    by .44mag
    Replies
    1
    Views
    361

    :roll:

    :roll:
  8. Replies
    5
    Views
    384

    Yup

    Yup
  9. Replies
    3
    Views
    500

    :doh::laugh:

    :doh::laugh:
  10. Replies
    4
    Views
    656

    Sticky: Jet/Marathon gas in Harlem now has two pumps for...

    Jet/Marathon gas in Harlem now has two pumps for non ethanol gas. 87 octane on Gordon hwy, (278/78, GA10). Also the circle k on 221 hwy at Columbia rd between Harlem and Appling in Columbia county.
  11. Replies
    13
    Views
    754

    Just an update. My boat will hit 56 mph according...

    Just an update. My boat will hit 56 mph according to my gps, 56 to 56.2 reading. That's with just me half of my fishing gear, one tank empty and the other full (1/2 fuel load). With my son and I, all...
  12. Replies
    116
    Views
    13,150

    Got it thank you again.

    Got it thank you again.
  13. Replies
    116
    Views
    13,150

    Just sent a PM with email. Thanks for sharing.

    Just sent a PM with email. Thanks for sharing.
  14. Replies
    4
    Views
    2,771

    Lol

    Lol
  15. Replies
    3
    Views
    147

    Yes it does, wish I could've found that earlier....

    Yes it does, wish I could've found that earlier. Now I need to order #38 as it broke.
    From looking at this, and thinking back at how clean the other spring was, it just happened to be laying on the...
  16. Replies
    3
    Views
    147

    The linkage is for the FNR cable that I'm...

    The linkage is for the FNR cable that I'm speaking of. One spring one stud to the arm that goes to the front of the motor. The bottom square piece that slides in the bracket fell and there was also...
  17. Replies
    3
    Views
    147

    Shift/throttle linkage at powerhead

    Ok I'm a dummy, get that out of the way. 1983 mercury 150 SER. # 6431959.
    Ok so I pulled the powerhead to replace the gasket (s) associated with and the base plate. All that went fairly easy....
  18. Replies
    24
    Views
    1,149

    LMAO :laugh:

    LMAO :laugh:
  19. Thread: Old Men Rule

    by .44mag
    Replies
    44
    Views
    2,494

    Hum nobody can see my house so I just forget...

    Hum nobody can see my house so I just forget about them. Maybe run over them with the lawn mower and mulch them once or twice.
  20. Replies
    112
    Views
    11,555

    Current----2015 Dodge Ram 3500 DRW 4x4 manual...

    Current----2015 Dodge Ram 3500 DRW 4x4 manual transmission 408 cid cummins and will most likely be my last as I'm not fan of automatics.
  21. We had a bull that would chase us when we was...

    We had a bull that would chase us when we was kids.....

    City boys that's a she :smile:
  22. Thread: Tow/Haul

    by .44mag
    Replies
    83
    Views
    3,288

    Never, I got a hair over 1100 Lbs/ft of torque...

    Never, I got a hair over 1100 Lbs/ft of torque and a manual transmission, it shifts when I tell it to. :roll: Sorry couldn't resist. The wife uses it with her Suburban and the horse trailer.
  23. Mornin, scrambled eggs for me

    Mornin, scrambled eggs for me
  24. Replies
    29
    Views
    1,609

    Best snake I see is at end of my 12 ga.

    Best snake I see is at end of my 12 ga.
  25. Replies
    12
    Views
    639

    Think he meant cut the ply wood in half then put...

    Think he meant cut the ply wood in half then put the two sections together making it 4 x 4 x 1 1/4 (instead of 4 x 8 x 3/4). Then use the cardboard template to cut the corners and such to fit. Not...
Results 1 to 25 of 146
Page 1 of 6 1 2 3 4