Was in the middle of sitting on my new boat and had to stop for a couple month. Have a brand new GPS Garmin 943xsv and a 100 gallon fuel tank. When I was setting it up I put it as a 100 gallon tank....
Type: Posts; User: maineidyl
Was in the middle of sitting on my new boat and had to stop for a couple month. Have a brand new GPS Garmin 943xsv and a 100 gallon fuel tank. When I was setting it up I put it as a 100 gallon tank....
Did inline filter to reservoir, check valve on starter side and check valve under the reservoir. Working perfect now. Not sure which one it was. Did oil prime on pc and bled air on reservoir after...
Thought manual was showing arrow flowing to main tank. Found pic of the original filter indicating flow direction towards motor. And the design has changed. If you compare original to new they have...
Replacing the inline oil filter that comes off check valve line under oil reservoir. Pulled without looking at direction. My shop manual does not show clearly the direction arrows and shape has...
I am horrible with this. Does that mean if I calibrate my new tank with my SC1000 it will use those settings when I add the Smart Craft connect. The connect would be my primary when received. The...
Quick question, boat is currently sitting with an empty tank. Just ordered a Smartcraft Connect under helm set up. Product won't be here for almost a month. Can I do my fuel tank settings etc. put 10...
Putting together my boat. Did my oil prime sequence and started motor. Loosened cap on reservoir and ran after prime sequence since that took a bit out of reservoir. Reservoir won’t fill. I checked...
Sent email to European. Rhonda shipped a fuel sensor. Trying to decide if I want to link to my Garmin 943xsv or the 403 or 502.
532370â€this is the tach. Works perfect on motor now.
Trying to go NMEA2000 on my XS. Currently have a Smartcraft Tach. The rear has only 8 pins. Connector to gauge has female with 10 openings but only 9 wires. There is a black and yellow that is not...
Thanks Joe. Appreciate you always answering. Thought I was screwed.
Tom
My starter motor actually will rotate in the bracket. All four bolts are as tight as I can get them. The outside part to the starter is not rotating it’s the starter itself within the case. Is that...
Found an original oem replacement for my trim pump locally. Thought it would be a quick job. One bolt broke off in the assembly. So my 1 hour job looks like it’s going to take a little longer. I have...
528478Going to email Rhonda
Tom
Was told by a friend that the Sierra replacement is not a bad unit. Almost cost as much as OEM. He is only had his for a year though not sure if that’s a glowing recommendation.
Need to replace trim motor on my 250xs. Serial number 5465262. How difficult of a job is this and if I cannot find OEM what is everyone using as a replacement part.
Thanks in advance
Tom
2006 Mercury 250XS
Serial Number 1E001830
<Serial Number 1E001830>
What Mercury side throttle is recommended for a 2006 Mercury 250XS?
Thanks in Advance
Tom
No idea on motor serial number other than it is a 20 inch 2.4 200 Mercury. Found more water than oil in my 2.4 lower unit. Pulled bearing carrier to replace seals and the roller bearings fell out...
Arrows on filter contradict the design. Not sure it matters as long as arrows are correct.
474645My new in line filters contradict the design of my old ones. Anybody else notice this. Parts are oem Quicksilver. 474644
Doing some maintenance on my 250XS. I bought three oil filters based on my manual. The two that are the same size were there. The larger in-line filter near reservoir was not there. Was there any...
Welsh plug
Tom
That’s where the confusion starts. I don’t have any of those on my motor. And the set on the motor never came on the motor nor did the wvm.
The motor id isC149576Bought as a 200. Was told it was a 135 and a 150 by someone else. Don’t see the WVM carbs any where for a 135 or 150. Wanted to try the wh carbs because I know that set is...