somewhat. It’s not very fast to remove for sure. I found small small areas to get it in behind the Jack plate and made myself an aluminum wedge to slowly pry off the parts of the Jack plate still...
Type: Posts; User: kuee95
somewhat. It’s not very fast to remove for sure. I found small small areas to get it in behind the Jack plate and made myself an aluminum wedge to slowly pry off the parts of the Jack plate still...
when you are in front of the grand jury you have to prove reasonable fear of death. If you were to show that video to the grand jury of then raming the boat and of you saying "wait let me put my rod...
My CHL training told me "Deadly force meets deadly force". in that video there is no deadly force being used. Doubt it would turn out well for the shooter.
It also depends on who owns the body...
I will double check. Always bugs me I have to jump through hoops to get it to read when first turning it on.
I had a similar issue. Most likely you are not looking at the correct transducer and you are trying to view the 3N1 while running which will not work since it is out of the water when running on...
Best Boat Wire is where I got mine from.
No kit but they do sell all you need to get the job done.
I pull my ZX225 with a 2017 Tacoma. No problems.
I have my 2019 Yamaha 225 SHO connected through NMEA 2k to my HDS Live units.
I can see Engine data under the Info icon on the home screen.
The manual says that once the Engine is connected...
If you decide you need the plates, I have a set that I never installed as I did not need them on my boat. $65 shipped.
Better Cranking Amps, but same Reserve Capacity.
If you have an Ethernet network installed there is a NMEA to Ethernet box available.
Then you can view the data on your Helix.
I did that on my Helix 12 before upgrading to Solix.
If...
I am running quite a few electronics on my boat. A ZX225.
I have dual 12" Helix on the Bow with a 360.
I have dual 12" Solix at the console.
Dual Ethernet Boxes.
Dual Power Poles.
Soon to...
I saw those instructions.
Questions:
1: So I fill the bilge with some water and put in the transducer and it will read the depth to the garage floor?
2: Or do I need to fill with water...
I did not do "proper" testing. I made sure it was functional but then installed it next to the existing one. I figured being so close to the existing one I should not have problems.
I'm a...
My boat came with Helix units and had a XP9 transducer in the bilge. I swapped to dual solix units and installed a XP14 very close to the XP9. Just a few inches further back. I get good readings,...
I just see an X for the picture. Even tried another browser. My issue I guess.
Yes the units are connecte via ethernet.
Not sure why my description and my signature don't match.
"Dual...
There is no picture.
Should my setup work as I described? Or do I need a Y-cable. (720103-1 14 M SIDB Y)
???
I have noticed the same thing. As much as these units cost, it is absurd that we have issue with basic functionality. Depth readings, maps?
Hope they fix it soon.
I will need to check that next time out. Or maybe I can get it to reproduce the issue in the garage.
I have two Helix 12 units at my bow. One is DI G2N the other just GPS G2N.
I have a 360 networked in my install and I am using the US2 transducer from my Ultrex.
I usually have one unit set to...
Best not to "coil" up the cables. The Solix instructions below have some words about what to do with excess cables.
Coiling them in a loop just creates a nice coiled antenna. Best to fold them...
I have two 12" Solix on the console. A SI G2 on the left and a GPS only on the right.
The Mega Transducer is hooked to the left one and I have an plain in hull transducer hooked to the right...
Can you share some partnumbers. Interested in doing the same.
I am in the same boat, no pun intended, except I am installing mine myself. Varying opinions on if you need new bolts or not. Some say, new bolts every time, some say the torque used is so low for...