With the current software versions, I have found it easier to build the instrument panel starting with one of the built in templates and then simply editing the sources. In your case, you would then...
Type: Posts; User: Mark O'Neill
With the current software versions, I have found it easier to build the instrument panel starting with one of the built in templates and then simply editing the sources. In your case, you would then...
Looks and sounds like you have at least two Structurescan sources on the boat. With Structurescan, just like with sonar you can get interference (crosstalk) so those sources need to be managed. ...
I can try and clarify some of this based on my experience with the products. Ping sync is available on HDS Pro units, the S3100 hub, will work with AT2, but will not work with older products such as...
You can use a Lowrance HDS Video Adapter cable, number 000-11010-001 as long as your Aqua Vu has a composite output (yellow plug).
HDS PRO has the ability to designate the function of the yellow wire from the power cable. Now, the yellow wire can be used to either “wake up” remote devices such as Active Target modules or the...
With the temps you are talking about, I would just leave the units, but I also would not wrap them up, as that can capture moisture that can freeze. As a rule, I remove the units that I have that...
Go under Active Target-More Options and see if there is a Source option, many times the unit is looking for the old version of the software, so re-choose the source.
restore
Not really sure where it says that a hard reset is recommended after doing this update???? The reason a restore is recommended is that when you do that, it resets the Active Target...
I have not looked into this subject in a number of years, but I am pretty sure this no longer works. I would agree years ago there were software versions that would do this, meaning to sync deleted...
The 23.3-67.3.26 version of Active Target was never released partially because of the timing of the cyber issues with Brunswick, while the versions of the same for the MFD's were released. Only...
Both AT and AT2 are capable of displaying sonar, that is how both get their depth reading. I would not suggest using this as a primary sonar source as the scroll rate is very slow and while will...
From what I have seen 3D Structurescan is still a supported product, so as a result updates are possible.
Attached are two images from earlier this year using a HDS Pro with AIHD 3-in-1 transducer with current software version. Images are compressed some to be able to post on this page, but I think they...
You really need to check which C-Map charts are installed on your Live unit to help you decide what to do, as there are a few different installed version possibilities based on the age of the Live...
The Hoffman Estates, IL Cabela's service department has one, brand new in the box. If you call ask for Steve in service department, they have it and not the actual retail store.
I use similar setup as TC, use a 23Ah LiFePo4 with the battery and AT hub in a case where I can plug in the Ethernet from the hub to a unit on bow or the stern, depending how I am fishing.
I would think the issue is the AT2 is at operating system level 67 (67.2.15) and the released software for the MFD's are at 65 (65.1.18) and there are some slight communication issues. This is no...
Go to Sonar-Installation-Source Name and enter name you want.
If you can afford it and especially with the sales at Cabela's/BPS going, then buy the newer technology and buy the Live. But just to clarify so you have all the facts, the support for Carbon units...
000-00128-001
That is incorrect, the original AT is more than capable of running two at once.
Combine red and yellow, put on switch and shut off when you move, turn back-on when needed. MFD will show "no source" when box is off and when you turn back on it will come back on.
The Lowrance bracket that comes with AT will work BEST for one specific depth and one specific distance from the target. So unless you only fish in one specific depth range of water and a specific...
It should go through three cycles and then give you the option to check a box in middle of screen to not see that message again, click that and the message should be gone until you do update or hard...
Delete waypoints and Purge, do a Restore Defaults to reset settings to new and that is all that is necessary. No need to do soft rest or hard reset, as those are only needed for troubleshooting...