Search:

Thanks for your reply. Both installations look great. Looks like you both used comfortroll trays.

I have my boat out of the water and in my shop. I’m trying to find a hull leak I may have to take...

Rodney, the support you cut was it a deck support or hull brace? Did you cut the deck with a grinder or sawsall or plasma cutter? Any problem using the pedal, it’s way up in the bow, do you still...

Long story short - it seems i had a micro sd card that was/is kaput - came out of my gopro bag - bought a new card and it's all good. Both units updated to 3.8.

I do appreciate all the help...

I recently installed two 93sv chirp units - both show software vs. 3.6. Garmin shows 3.8 is most current. I follow the directions per Garmin but the 93sv does not offer to update when I plug the...

Thanks for the insight. Yes, the two lakes I fish most are listed as being "maxdef". They are also COE lakes and are currently about 10 feet below full pool. I was on the lake one day when the Garmin...

One more question. If I had the lake vu card at the helm and a regular micro sad card at the bow and if I marked a way point will it still share to the other unit? Assuming the two have been properly...

OK, so if my lake is 10 feet down - the mapping will be adjusted to show only the contour lines 10 feet down and below? If I assign colors to various depths will the colors also be automatically...

I'm replacing my old Lowrance 332c's bow and helm - putting a echomap 93sv on the helm. My question is on the bow - is sideview any use on a trolling motor? I started out thinking I would mount a...

Dowco made the original G3 covers for this boat. If you still have the original trollng motor, their cover is "custom" patterned for the hull. You will need to order it with no buttons installed -...

Casey Ashley, knows the lake. The weather is the wild card this year.

I pulled new 6 gauge thru my HP180 several years ago. I just duct taped the new to the old 8 gauge, took off the plastic bow cover plate and pulled. No problem at all. I did have to watch the back...

2012 G3 SunCatcher 325 Dlx - yamaha 250 sho - 26 ft long with rear loungers and captains chairs on port side -It will chase 50mph but you better be near a gas pump. Cruises at 17/18 @3000 rpm which...

I just replaced my Interstate "24" with a Sams Club Duracell 34m - about the same size as 24 - but is an agm battery made by Deka. Never have to check or add water to an agm and its cca and mca is...

2013

I feel like a freaking idiot - assuming is never a good thing. Fuel line crimped and the motor ran out of gas. There is some blowby fuel in the crankcase but tech didn't think it was necessary to...

New 2013 250 SHO with 4 hours on the clock engine dies in the middle of Lake Hartwell. Pull the cowling and check the dip stick there is gas in the crankcase. I assume that the motor has hydrolocked...

I run a 24p Trophy Plus on a Vmax 150 2stroke - it is much easier to drive and trim vs the 25m three blade . I assume you have added a blow out ring to the prop?

At wot I can trim all the up but...

Read my earlier post, not sure what the difference is between Trophy and a Tropyhy + ...
I would like to find a large hub 4 blade (cheap) - you will need a blowout ring on that Mercury prop.

The vmax 150 will turn a 25p just fine - around 5500 rpm @ 58 to 60 mph
the last 5 mph are hard to get & keep not a real pleasant ride.
I have a trophy 24p that gives the best all around...

If you are concerned - why don't you just pull 6 gauge and not worry about it.

I have never fished from an Eagle 190 - looked at one in the show room.
I think the HP 180 will give you a better fishing platform up front and it has lots of rod storage.
The vmax 150 carb motor...

Last year I upgraded my tm, I considered 36v, thought I could pull the starting battery from the transom area to make room for the #3 tm battery and relocate the startrer under the drivers seat or...

Only other option is to build the front deck up - like a flats boat - and sink the pedal close to the bow. Might work.

My Hp180 came with a 55# 12 volt 5 speed - Lived with it for 4 years - two batteries in parallel. Recently replaced with a MK Maxxium 80# - grabbed a good deal from Cabela's - shaft is a little long...

I went to a trophy 24p - 4 blade. Really lifted the stern - no porposing with two guys, full gas and live well. Also steering is much better not near as much torq
at wot. Trim it down, cut the...