Has anyone dealt with Hodges marine? I'm looking for a new navionics card and looks as though they have the best price just never heard of them before
Type: Posts; User: deputyb716
Has anyone dealt with Hodges marine? I'm looking for a new navionics card and looks as though they have the best price just never heard of them before
So I had my boat at the local dealer and while it was there, my hds12 was stolen. It was originally flush mounted but now looking for a better way to mount so that the electronics can be removed.
...
I'm currently running a g2 on a z520 with a raker ho 26 prop. I'm adding a bob's 6" action plate this winter. Will i need to change the prop? if so, suggestions? :salute:
:thumb up2:
I have a g2 250 on a ranger, looking to add a 6" jack plate this winter. Currently running a raker 26. Would I need to re-prop? Suggestions?
It has been running like a charm.. with just me onboard and all my gear and slick water, can get about 76. Looking to add a jack plate this winter so hoping to hit 80. Happily take ya out on a...
Too funny... .I sure need to laugh right now!!
You misunderstood... I'm not denying responsibility for the lower unit. I think it was a stump based on the area. I was only barely in gear and not on plane. Most likely, had I stayed on plane...
then the next question will be how much my insurance will increase?
Well, finally got my boat back and had the fuel pump and a valve replaced. Now I have a bigger and more costly problem........
Anyone have an idea on how much its going to cost to repair a lower...
I didn't realize this until now, but they are not Platinum...... Mark's Marine in Grimesland NC. I refuse to go back to the dealer I purchased it from (bad customer service). I'm hoping it is...
No, it originally broke the swivel assembly on 5/22. Dropped it off at the mechanic that week. Picked it up on 7/8. Took it out for a test run on 7/12 only to have the problems above. Took it...
Well, I just dropped it off. Third, 4-hour, round trip to the mechanic. Hope they and brp can figure it out. Boat has been out of commission since 5/22. Maybe brp will give me some gas $$$.
Ok tech guys.... help me out here. 2015 G2 on a z520c. Just got it back from the shop due to a swivel assembly that needed to be replaced under warranty. Took it out Tuesday and ran fine on the...
Be careful when you are power-loading your boat. My g2's tilt/trim just broke while pushing the boat up on the trailer.
http://www.bbcboards.net/attachment.php?attachmentid=239057&stc=1
I have a 2015 G2 250. The tilt apparently broke on Sunday after trailering. I ws barely able to get the boat home as it left the skeg just a few inches off the ground. The engine was in the upper...
I have a Dobyns rod with a damaged eye. Anyone know of a custom rod builder or anyone else that could repair the rod in the Raleigh area?
Dobyns advised they would send me the eye for free but...
http://www.bbcboards.net/attachment.php?attachmentid=225839&stc=1
2015 Z520C / G2 250/H.O.
Lowrance Gen3 12 - console
Lowrance Gen3 9 - bow
Power pole
MK Terrova 112
That's exactly what I want, I'm just curious on mounting options? I have a 2012 chevy truck.
ok, i'm looking to add a set of led lights to the back of my truck (up high) so that I can see in and around my boat while getting it ready in he very early mornings before sunrise. I typically...
Other than the BS... I love the boat especially with the new G2 Evinrude. The torque is awesome, fuel economy is better than expected. Top speed I've had it is 75 mph.
It most certainly would be, unfortunately.........
Well, to be honest, I "thought" i was getting a pretty good deal............ I went to them and got a price and the dealer I purchased from did beat it, but after everything that has happened, I...
Purchased my "dream rig" a couple months ago. Wanted a couple things upgraded on the rig, which included the MK 112 tm and gen3 electronics. I got the TM installed before taking possession. I...