but there are a ton of refugees who migrated here through the years.[/QUOTE]
Shame that Al didn't close the border before Jerry T got in.:doh:
Type: Posts; User: SLEEPIN RANGER
but there are a ton of refugees who migrated here through the years.[/QUOTE]
Shame that Al didn't close the border before Jerry T got in.:doh:
Morehead City, North Carolina :beers: One of my favorites :yesnod:
Damn Fred :laugh: Forgot how pretty I was. :doh:That's when da Chicken asked me to marry him.:laugh: Or was it Jerry.:doh:
:doh:Damn....all you old boyz sure bring back some great BBC memories. :beers:
Sorry bout the hijack:doh:
:yesnod:Yep they come one size fits all...........same for the boots.:laugh:
Who you laughing at Junior.:yesnod:
gave up on the beavers started a goat rental business with free boots.:yesnod:
I check in on you old geezer's once a year or so to make sure the big kahuna
is keeping an eye on ya.:beers:figured you Mike, Fred, Al, and the boys were entertaining at the old folks...
Knowing Jerry it had to be a goat.:doh:
Yep that boy is the best thing to ever come from a sperm bank. :nanner:
Pull the center cushion of the left and right seat backrest out (Velcro Attached) remove the 2 screws on each side. Fold down center seat backrest to gain access to the 4 screws at top of panel lift...
The 25t is the best setup for your boat, motor. The 27t will be too stiff to turn, especially in summer. You will probably loose about 200 rpms. That motor needs to be propped to turn at 6,000 rpms.
Taylor ms is correct. the 27t has the upper part of the 2 piece thrust washer still in the hub. it will pry out though, then you could use the 27 with your existing single thrust washer. I recommend...
I Just got back from Hydro Tec. for a power head replacement. Great group of folks to deal with, excellent customer care and service, very reasonable prices. You couldn't find a better group of...
Praying for a full recovery for Andrew, and prayers for Greg and Sandra.
Amen...+1 :thumb up2:
:thumb up2:Ordered one today from ranger, as Howie said $76.85 :thumb up2:Well worth the price to keep from banging my head and the gravel from my knees, will save a lot of wear and tear on an ole...
oops
Had similar symtoms on my 03 250 HPDI. Hole shot was a little sluggish with slight surge around 4500 rpm, lost about 200 rpm on top end,
from 6K TO 5800, not as much as yours. Turned out to be a...
You will see the leads under the console taped to the main harness. They have three open ends with red butt conectors on them. The easiest way to determine 1, 2, or 3 would be to touch acc1 and use a...
I just recently had the same issue with my 250 HPDI. Found the tuner water passage in the exhaust plate stopped up with sand.Drilled passage out about 2mm over and Replaced with the Hydrotech...
:thumb up2: Thanks Rich, makes good sense, I should of thought of that :doh:and i always believed that beer only killed off the weak brain cells. appears it going after the good ones too :laugh:...
Good morning guys :mug:
Can anyone identify the tuner water passage to enlarge from the attached photo's and what size drill bit to use?
As usual thanks for the help. :beers:
...
Taxidermist......been mounting and stuffing beavers for over 45 years :smile:
thinking about retiring and starting a sheep and boot rental business. :beers:
Im always around, just fall asleep alot:doh: I check in on you guys quite often, just to be sure they still give you a hard time.:laugh: Looks like they are keeping you busy.:laugh: