Search:

thank you sir! I"ll give it a try. Cheers!

Hi folks,
I have a 2000 201D with a livewell that doesn't work on "intermittent" if you will. Works fine on constant but I would like the other option as well.
I suspect that it is the...

Don, PM sent. thanks.

Thank you gents.

Hello folks, as the title says...I was out yesterday and on the way back to the ramp engine just shut down as if I pulled kill switch or turned key off. Pulled cowling when I got home to discover the...

Thanks folks!
Hope all is well Don, been a while since I have posted.
Good to see you're still runnin' the show!

Cheers.

Hi folks, my engine oil tank was down about an inch from full this spring so I cracked the cap, ran engine until it was full to the
top and re-tightened cap. I noticed yesterday, 1 month later and...

-TorqueMaster Gen 1 "GEAR CASE"-20 inch split shaft. Shafts will need to be cleaned up.
-Comes off 2002 Mercury 250 XB.
-Case/housing is near perfect except for small 1/4" notch on skeg (see area...

Anyone have a reasonably priced motor, $500-$600 range (exchange is brutal) and willing to ship to Canada?
I will pay for shipping of course.
Don't need universal sonar, but must be 45" shaft and...

Hello folks,
My cable binds a bit at the last inch when coming off throttle and I have to sneak my toe forward of the pedal and pull it back to zero, or idle.
Time to change it but...

as always...thanks Don!

Hello folks, I need to replace my throttle cable this spring. How do I go about finding the right length, model etc.?
Is it as simple as fishing it out, measuring and ordering? Or is there some sort...

Ok it's been a while, but I finally got around to putting in a Merc pulse fuel diaphragm kit. BINGO! All good.
Sierra kit looked like crap quality compared to the Merc kit.
thanks again gents!

Hi folks, my turn to ask a question...:smile:

I have a dead livewell pump. I have the old Mayfair yellow cartidges and I was wondering
what I can replace them with?

Thanks!

Hi folks, I've been trying to get around to installing the tray I bought over a year ago...and finally found a few hours this morning.
I've done it before on a '99 201 it was very straight forward....

Hi folks, like the title says, I have a Gen 1 case in perfect shape but gears were rattling so I replaced it.
It came off a 2001 ProXB I used to have.
Split shaft model.
What's it worth?
thanks

thanks Don!

Thank you gents!...forgive my bozo-ness but what do you mean by check valves? what are they and where are they found? In the diaphragm kit? thanks!

Hello folks, here's the low down:

-150ish hours on remaned Merc P/H
-compression at 123-125 across the board
-new Merc primer bulb and all new hoses
-Sierra pulse fuel diaphragm kit changed (...

Hookahawg, what is your p2p? I’m sitting at 3.25 below as of right now.[/QUOTE]

Honestly... don't know, have not played around with it. It ran good as is when I bought it so I didn't touch...

I have a 2000 201D with a 2000 Merc 225 EFI, 10 inch Z-Lock and 25 Tempest. I used to have a '99 201S with a 250XB, 12 inch RapidJack and 25 Trophy.
My current setup is faster out of the hole than...

hahahaha.... that was funny,,,but sorry to hear that bro:ohwell:

Just make sure they get down into the stringers as well. If your transom is soft, there's a good chance the "rot" or wetness may have made it into other structural areas as well.<br>
If you replace...

Thank you, however...next morning in the driveway update: turned key and motor started right up....weeeeiiiird...
Incidentally, starting battery is a barely 1 year old, group 31, 1125 cc and 925...

***Serial # in signature***

Hello guys, engine runs great, very strong (new reman Merc P/H with maybe 80 hours).
I was out yesterday and at one point I turned the key to "ON", engine went through...