New bowls have had high speed jets transferred. I was very careful about that.
thanks
rcb130
Type: Posts; User: rcb130
New bowls have had high speed jets transferred. I was very careful about that.
thanks
rcb130
ChampioNman, Jughead,
problem with excess smoke has gone away. new carb bowls, rebuiling carbs, replaced a couple of loose clamps on fuel lines and it runs without
all the smoke from before. Just...
ChampionMan,
too short for float pins. these were split down the long axis and hollow. about 5/16 long. All other carbs has float pins installed correctly as did the one with the extras.
rcb130
While rebuilding the carbs on this motor I found 6 small roll pins in the carb bowl. They were in the area of the needle valve.
Figure that one out.
rcb130
OMCforever,Jughead,
OMC, I have the "real" service manual. I was hoping for some old time tricks to figure this out.
Jughead, Thanks for the tips on where to look and how to check.
Thanks
rcb130
Hello all,
Working on a 1998 Evinrude intruder Model E150GLECD, S/n GO4357082.
This motor smokes really bad. I have found several air leaks at the carb bowls and I am in the
process of replacing...
Ok, but why only one carb getting overoiled? The other three carbs were normal.
rcb130
Joe54,
Thanks for the tip. Will try it once I have carbs back on motor. Here is another one for you. When I opened the float chamber on #4 carb(lowest one) I found mostly oil and very little gas....
Hello,
Motor is a 1999 Merc 115ELPTO, S/n OG866225
All new filters,spark plugs.
question: How much fuel should the choke solenoid eject in a specified time, say 15 seconds? Should it be a strong...
Joe54,
I do not think it is an aftermarket stator. It is P/n 398-832075A 5, a 16 amp red stator from mercury. I have also found out this stator has a module attached as part of the stator assembly....
Hello All,
Motor in question is a 1993 Mercury Mariner 3 Cylinder, S/n D175357
While checking the motor for a low speed miss, I was tracing the wires from the stator to check the low speed winding....
Hello All
2002 Johnson 175 carbed
Model J175PLSNF
S/n 04987410
Quick question. Are washers to be used under the needle valves on the carbs? Is there a chart or something that would tell me when...
Yam911,
thanks, that is exactly the info I need.
Be Well
rcb130
Does no one know what this is and how to set it? Where are all the Yamaha experts? Help needed. please
rcb130
ChampioNman,
What would you suggest I check next?
rcb130
Hoses are correctly connected.
I have replaced the throttle body to intake manifold gaskets.
Metering holes in throttle body are all clear
rcb130
ChampioNman,
yes I am referring to the white nylon o rings. I have removed the old gray fuel line today. Which hoses are you referring to on the engine side?
thanks
rcb130
Motor is a 1992 Johnson v4, 120HP
Model J120TLAND
S/n GO3002936
Are gaskets used under the needle valve seat on this model?
I was working on this motor last year and never was able to get it to...
Hello all,
Motor is a Yamaha 40 SGJD, 1988.
On the cdi unit is a metal pointer that moves as the throttle is advanced. How do I know if the pointer is in the proper place at idle and what is its...
ChampioNman or Jughead,
What do you think of my last post? What to check next? shot size?
gentlemen, I am back.
New paper gaskets in place. New fuel pump (OMC 438559) in place. Same problem, runs on primer fuel and quits. I am still not able to get a firm bulb. Where can I get the lead...
ChampioNman,
You are spot on with the air leak problem. While waiting for the intake manifold gaskets to arrive I checked a few other things.
With everything hooked up I cannot get the primer bulb...
Should these carbs have the gaskets under the float valve seat? They were there when I removed the carbs to rebuild them so I installed them on the rebuild.
ChampioNman and 316jughead,
thanks for all the help so far. I have ordered new paper gaskets for the intake manifold. There was very little junk in carbs. Calibration pockets are clear, alcohol...
No allen head screws visible. Carb mounting gaskets are new, part of rebuild kit. I did find on the fuel distribution manifold a pinched outlet nipple. I have ordered a replacement manifold. I do not...