Correct..And the other Renegade models look like that, as well.. Yes, they have Lund's IPS hull which does have a pad. The hull is V shaped to the back but with a pad in the center as it...
Type: Posts; User: T-Mac
Correct..And the other Renegade models look like that, as well.. Yes, they have Lund's IPS hull which does have a pad. The hull is V shaped to the back but with a pad in the center as it...
They help spread the weight and keep the stern higher in the water and negate bow rise, thus keeping the prop higher on acceleration and at lower speeds.
10-4 Yes.. GPS..
Non GPS is like blowing smoke. ;)
Mike...... It isn't a perfect science. When we test them they have a fair amount of fuel, but the boat isn't loaded up like a tournament load... We make several runs with GPS .to get a range of...
..... X7 17Spitfire performed best of the props we (LUND) tested on that model.. We hit 47 with 2 guys, full tank ..BUT little else in the boat.
Look for wide chine width. Beam is width at the gunnel and doesn't effect stability.
Width at the chines yields the "footprint" . Wide foot print
yields stability.
www.lundboats.com Almost all of your questions are answered.. even some of the performance questions and specs (Red Book Section).
-Here are a few quick answers, however:
#1 The pumps are...
I just replaced the demand valve on my small boat...(replacement suggested by a good tech). My question is : Why is it needed on the gas line on a portable 6 gallon tank with a vented cap..? I was...
Congratulations :beers:
A new 50 Merc 4 stroke with very low hours..with demand valve on fuel line and vented cap on portable tank: When cruising on plane at 20mph GPS and about 3500 rpms on a long run... after a...
Yep.. I sold jons with jets (O/B's) on them for years --- it often doesn't take much at all. Some Jons have a small hook welded into the hull, at the transom - on each side,and that works fine,...
Ok. Whatever, I guess (?)...But, the exact purpose of those factory tabs is to adjust and eliminate porpoise. They are found on many brands.
Unfortunately, you could have saved a lot of money.
I'm going to guess that boat has some tabs sticking back past the transom...(extension of the hull running surface).
If those are present, they are adjustible. They are to be manually adjusted...
Aluminum hull shapes vary. Jack plates are benificial on some aluminums more than others. For example, Lund hulls (including the Pro V Bass and Renegade) do have a "pad", thus the prop works in...
Check with your Lund dealer . Lund offers at least one model tool holder (for the sport track) for Pro V Bass models
Many boat DEALERS sell Karavan as the trailer they package their boats with. Those dealers get the trailers from Karavan and the rest from the boat, engine, etc companies. Although there may be some...
The regular Pro V models are very roomy up front.. The are the same hull as Pro V Bass, but with with more freeboard.
I don't see that as a realistic project ...$$-wise. The consoles on the Pro V Bass are totally different than the ones on the regular Pro Vs with walk-through windshields. The Pro V Bass consoles...
I went roller trailer on my 1650 for the same reason.
I have a 2022 Angler (tiller). I didn't get a chance to run it much before old man winter hit.. but I am impressed with how it behaved and how it fished.I like it better than the 1600 Fury and 1625...
The construction material isn't as important as the physics involved . The operative factor is the amount of freeboard exposed (to the wind) above water line -vs- the amount of hull in the water. ...
Built by Crestliner. Welded. Built at the plant in Little falls,MN at the time. .. Owned by Genmar, as was Ranger at the time.
Merry CHRISTmas !
Texoma... I sent you a PM.
I had a couple LE's, myself. A 1900 and a 2025. Al Lindner and Gary Roach were the ones who came up with that layout. I agree, they were an excellent 2- man fishing platform, for sure.