I don't think I was inpatient by the looks of the timeline of this thread but thank you for the info and I'll keep that in mind
Type: Posts; User: RICH2113
I don't think I was inpatient by the looks of the timeline of this thread but thank you for the info and I'll keep that in mind
Lockemans got it fixed had I had a new water propeller put in .big thanks to them . Championman when this thing started I wasn't even talking to you I guess everyone is aloud their 2 cent ... To bad...
Wow .... just thought I put this out their...what are you a bully...seahorse was talking about the lower unit but thanks for your help..Sorry to bother you seahorse thanks
Little info
Your burning the propshaft seals is pretty rare but it does happen occasionally in boats that use jackplates, in some tunnel hulls, and often when operated in water with plant life or...
2007 Evinrude E tech 150 serial #5175561 2008 power head less then 70 hrs on motor prop shaft seals burning out leaking lower unit oil this is the second set of seals I've gone through Evinrude says...
Wow thanks for all the info been busy taken care of some motor problems my prop seals are burning up had 2 sets burn up on me hope we got it taken care of , I thank I'm going to go with the hds 5 got...
The boat is set up with a 21 raker SS prop,from the dealer help set my boat up big thanks to lockemans
The top RPM this motor runs is 5001 5500 by the Print out
2007 Evinrude E tech 150 serial #5175561 2008 power head less then 70 hrs on motor prop shaft seals burning out leaking lower unit oil this is the second set of seals I've gone through Evinrude says...
Looking for something with gps and depth finder the hds 5.... I have to cut the hole even bigger and I really don't what to have to do that looking for something that will fit and take take care...
I have a 2007 183cx looking for ideas for the dish electronics my old 332lms went out and need a new one don't know what is out there and what will fit hey thanks
hey you can go to the henry ford museum and green field village. and go fishing
HEY! found the problem it was the main wire harness that connects to the fuse panel. there were 3 wires, the main red hot wire and 2 other wires bilge. and gauges that was badly corroded. the red...
Thanks Lea still working on it the boats wiring diagram would really help. just sent basin butch a message
Thanks Lea still working on it the boats wiring diagram would really help.
Thanks went out and unplug all the pumps and bilge float switch and the bilge switch on the dash stayed lit-up even in the off postion . going crazy
Went out to the boat and seen the bilge pump switch was light up and the main power switch was off check the pump and it was running check the float and it was down unplugged the float switch and...
Best of luck to you...we're all prayin' for ya Lea http://www.bassboatcentral.com/smileys/praying.gif http://www.bassboatcentral.com/smileys/praying.gif
http://i152.photobucket.com/albums/s196/RICH2113/STRESSCRACKPORTSIDE2.jpg
THIS HAPPENED TO MINE BACK IN 2008
HAPPY NEW YEAR TO EVERYONE HERE AT BBC http://www.bassboatcentral.com/smileys/newyear1.gif http://www.bassboatcentral.com/smileys/newyear1.gif http://www.bassboatcentral.com/boardstuff2/beers.gif
Merry Christmas and Happy New year to everyone here http://www.bassboatcentral.com/boardstuff2/beers.gif
http://www.bassboatcentral.com/smileys/praying.gif http://www.bassboatcentral.com/smileys/praying.gif
I have a e-tec 150 but this sounds like my problem I was having for every 100 rpm I would get a mph in other words if my rpm was 5200 rpm that is all i could get my speed would be 52-55 mph depends...
How much are the decals? How do I go about ordering some?
Yes I would. you might be able to take off the panel in back of the gas tank area and see whats going on but if I was you I would take out the gas tank , it would make working back their so much...