Search:

that's what I figured

would you get 2 x 12v or 1 24v? I believe the weight ends up being about the same

I have a crazy idea to purchase two 24v 50ah scooter battery packs wire them in parallel to run my 24v 80 # Terrova

anybody ever tried this? I t would be a lot cheaper and a lot lighter

My 24V 80# ipilot 60" gen 1 has been on my Stratos for 9 yrs now I dont use the foot pedal only remote
I mostly fish by myself so it helps me stabilize and move the boat while I'm fishing and tying...

I have had the proper HB shoot thru puck with epoxy on my stratos for 5 yrs connected to a dedicated HB 717 unit only for high speed and low speed depth
this summer it was not showing depth numbers...

Ebay, its called a trible air bag jack Got it for $200 Canadian
A guy near me imported them from China,..
It uses ar, raises anything in seconds.

423338 I just had my Stratos trailer converted from a torsion axle to a leaf spring.
with the new axle the boat sits much higher than it ever did almost 1-1/2" higher

Can I lower the trailer...

thanks, maybe I'm just thinking there was something wrong after I removed a whole bunch of fishing line around the prop shaft

Is the prop on a 80 lb terrova easy to spin by hand?
is it supposed to stop immediately?
mine spins but stops immediately, I have also noticed at max power my full speed is reduced a little bit...

My trailer needs to be replaced, but not sure what brand model or style to re[lace with.

its a 1996 single axle non brake stratos carrying my 1996 288DC.

I love the way I can put the boat back...

Thanks, I hope this will get it fixed, its more annoying than anything.

I have always been a proponent of using non ethanol premium fuel in any of my toys and gas powered tools.

In Canada, ...

I have a 96 175 faststrike J175GLEDB I ordered ne gasket and oring for the vapor tank but maybe I should consider changing the air orifice size?

not sure where to start and what size would help....

I have a damaged section of rub rail on my 96 stratos 288 dc and was wondering is there something i can cover it up with?
I was thinking a piece of poly pipe cut on a bandsaw and screwed on to the...

Thats what I was thinking,
Does the deive shaft just pop out or is there a proper way to remove it?
I remember just pushing it in until it clicked when I got the new unit 3 yrs ago

Last summer I noticed I was getting water in my lower unit,...so I would change my L.U. oil every 2 outings and monitor continuously
I was going to ride it out until winter and pressure test the...

Asking to know if I can store my boat without the gearcase on it to work on oever the winter months.

Do I need to do anything different to it, close off the exhaust port, etc,...?

I hit a...

would a transducer fail like that or would I start to notice little things first

yes been like that for 3 years no issues what so ever

fibreglass hull, but transducer is wired direct to the 998
it was working in the morning and when I went out for late afternoon, no depth showing, but si and di are working

I swapped the head...

My screen lost the depth reading on the screen, is there a way to verify the transducer
before I start removing it from the boat?
I swapped the head unit to the front trolling motor and the depth...

One of my Talon spikes is not staying attached, it comes right out,

I had to take off my talon from the bracket in order to move the boat in the water.

It looks like the o'ring is damaged, but...

My motor will stall after fishing in a shallow area where I tilt the motor out,
it starts fine but will hesitate and stall when trying to take off.
I think its starving for fuel,
I thought about...

I didn't think that there could be a way to hard wire the controls, I was looking for the non bluetooth foot remote but can't find it anywhere,
I actually keep the fob in my front pocket it stays a...

Any electrical engineers out there that know how to direct wire the talons for their deployment and retraction,..

I'm not sure if its even possible, just an udea as I can't find the non-bluetooth...

im also looking for one is the part # 1810256?

i think thats what has happened cause the bonding wire is loose I'll look again thanks