Search:

Type: Posts; User: densik

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    192

    If it was a 21 ft, then I can see it. Otherwise,...

    If it was a 21 ft, then I can see it. Otherwise, it was probably do to availability. All of them get very close, or will hit the rev limiter with the 25p-t2
  2. Replies
    13
    Views
    320

    Try switching the card reader slots. If it does...

    Try switching the card reader slots. If it does it in the new slot then it is the head unit or card. If it doesn't do it then it is the card reader slot
  3. Replies
    2
    Views
    247

    I use 2"

    I use 2"
  4. Replies
    2
    Views
    81

    Bass Boat Technology has one.

    Bass Boat Technology has one.
  5. In 2018 the ZX did not come with NEMA, but the...

    In 2018 the ZX did not come with NEMA, but the Lowrance Elite Ti's were connected to each other with ethernet.
  6. Replies
    14
    Views
    459

    I have run every one of my 20' R hulls with JP at...

    I have run every one of my 20' R hulls with JP at 16-18 and now with the 2" spacers that Skeeter has been putting on, my trim is all the way up. Then, when your speed flattens out 2 bumps down. 6000+...
  7. Replies
    2
    Views
    276

    If your Skeeter is a ZXR/FXR then the puck is for...

    If your Skeeter is a ZXR/FXR then the puck is for the trolling motor, and the trolling motor is a LINK model. You can use this for a heading sensor on your depth finders. Since you have solix units...
  8. Replies
    12
    Views
    507

    Doesn't matter if you pull the valve out running...

    Doesn't matter if you pull the valve out running or before you turn it on. If it comes out week, turn the power switch off and on quickly. May take a time or two, but it will spray to the top of the...
  9. There is a pull rope in every skeeter built after...

    There is a pull rope in every skeeter built after 2018, you need to look hard to find it. This will help get from the battery to the console. Going forward is easy. Transducer cords are usually laid...
  10. Replies
    2
    Views
    267

    Ultrex Link, and the 2 graphs

    Ultrex Link, and the 2 graphs
  11. Replies
    4
    Views
    249

    Was the boat ordered with the 52 shaft or did you...

    Was the boat ordered with the 52 shaft or did you have the dealer swap the trolling motor out. The covers are made for the individual boat and are a little different between the 45 and 52 shafts.
  12. Replies
    65
    Views
    9,713

    Reynolds from Reynoldsboats.com should be running...

    Reynolds from Reynoldsboats.com should be running his demo 21XE up on the St. Lawrence mid-Sept. supposed to be coming in very soon.
  13. Replies
    5
    Views
    375

    I tested a 24 and 26 on all 4 hulls ZXR/FXR 20 &...

    I tested a 24 and 26 on all 4 hulls ZXR/FXR 20 & 21. It did very well, but nothing I have found matches the 25-t2 on all 4 hulls
  14. Replies
    4
    Views
    505

    Run the plate around 7-8 dots showing. Then fine...

    Run the plate around 7-8 dots showing. Then fine tune from there
  15. Replies
    6
    Views
    728

    Because running high is not what throws blades....

    Because running high is not what throws blades. Running and having the motor leave the water while at full throttle is what does it. It may not do it on that particular day, but that is what gets it...
  16. So, if your batteries have an app similar to the...

    So, if your batteries have an app similar to the Ionic batteries, then you can turn your app on, select one of the trolling motor batteries, put your tolling motor on 10, then run it. With in a very...
  17. 95% driver error. I have been able to run any of...

    95% driver error. I have been able to run any of Skeeter's hulls for the past 20 years down to an average of 20 mph without any porpoise. Combination of trimming all the way down and feathering the...
  18. Replies
    6
    Views
    233

    With Skeeter nobody measures that anymore as the...

    With Skeeter nobody measures that anymore as the motors and jp plates are mounted the same every time. That is why that is all you are hearing.
  19. Thread: Zxr speed

    by densik
    Replies
    10
    Views
    723

    I run both the 20 and 21 for demos, the...

    I run both the 20 and 21 for demos, the difference with me driving and setting them both up is 2 mph on average.
  20. Thread: Zxr20 NEMA

    by densik
    Replies
    2
    Views
    215

    It does not. So you would need the NEMA backbone,...

    It does not. So you would need the NEMA backbone, Yamaha interface, and NEMA adaptor for Helix
  21. This is correct

    This is correct
  22. Thread: New Models

    by densik
    Replies
    92
    Views
    6,575

    Dealers meeting is next week. A 2k increase is...

    Dealers meeting is next week. A 2k increase is minor in the manufacturing world these days, and that is the result of the 10% increase that all boat manufactures applied going into the 2023 year. All...
  23. Replies
    3
    Views
    304

    10-12k

    10-12k
  24. Replies
    11
    Views
    599

    Check to make sure you are getting full throttle...

    Check to make sure you are getting full throttle before anything. Remove cover and have someone press the hotfoot. Make sure both hashes ar perfectly aligned on the throttle body. Once that is...
  25. Sometimes the box that holds the wire and...

    Sometimes the box that holds the wire and connects to the back of the unit has play in it. Try before all else to open the box and either wrap electrical tape around the power wire where it enters...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4