Search:

Type: Posts; User: randybenham

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    722

    Update - took back to dealer & re ran...

    Update -
    took back to dealer & re ran diagnostic- showing shift actuator still. They had another boat in w similar issue that was demand sensor. Still on backorder till mid June now. This sucks...
  2. Replies
    6
    Views
    722

    Bump

    Bump
  3. Replies
    6
    Views
    722

    Bump w SN attached

    Bump w SN attached
  4. Replies
    6
    Views
    722

    Yes. Pulled pos wire off battery

    Yes. Pulled pos wire off battery
  5. Replies
    6
    Views
    722

    Shift actuator vs demand sensor

    Could use help
    2019 boat w 4S pro XS 250. SN fell into shift actuator recall & part was replaced in 2019. Couple weeks ago, coming in from a derby day, solid alarm goes off after a 20 min run - try...
  6. Thanks guys. Think I've figured out the 150 4S...

    Thanks guys. Think I've figured out the 150 4S won't turn the 24.
  7. 150 merc 4S prop recommendation - Nitro Z7

    EA or other guru's;

    I'm running a 2015 Nitro Z7 with a 150 Merc 4S. boat was bought New, still in warranty. Runs like a top. recently added an 8" JP (manual) with hopes of gaining a couple MPH...
  8. Replies
    59
    Views
    3,836

    Any follow up from the agfc meeting on ouachita ?

    Any follow up from the agfc meeting on ouachita ?
  9. Replies
    59
    Views
    3,836

    Just FYI, I have heard that there will be a...

    Just FYI,
    I have heard that there will be a meeting to discuss fishing management on lake ouachita on 6/28. it's a tuesday. I believe the meeting is supposed to be at Mt Harbor.
  10. Replies
    3
    Views
    532

    I can vouch for these guys. reasonable & got a...

    I can vouch for these guys. reasonable & got a prompt delivery.
  11. MD please keep me informed. Mechanics ive...

    MD
    please keep me informed.
    Mechanics ive spoke With tell me the 6" plate will help top end & ought to really help chine walk.
  12. Mark my old motor was an evinrude. I bought my...

    Mark
    my old motor was an evinrude. I bought my razor from you a couple yrs ago. I kept the prop when that engine blew & traded in on a nitro.
    I ran the razor yesterday with mixed results on the...
  13. Yes they are. That's all I'll say about that.

    Yes they are. That's all I'll say about that.
  14. it is analog. I'm sure it's off by a little bit....

    it is analog. I'm sure it's off by a little bit. its the gauge that is in the nitro, so I agree on the accuracy. I looked up results from boat testing on the mercury website, & I'm right on with...
  15. So I took the boat out for a few runs to see the...

    So I took the boat out for a few runs to see the difference in the 24p razor.

    hole shot is fine up on plane in 3 seconds. 0-40 is pretty fast. when I trim up & get to 50 mph gps, it's a slow...
  16. Don, As I stated above, when I switch to the...

    Don,
    As I stated above, when I switch to the 24p Razor, it rubs up against this when I spin it by hand. I was just wanting to know what it's for. it doesn't rub on the 23p temptest prop. this is...
  17. Replies
    6
    Views
    693

    I have the 150 4s on a 15' Z7 & I like the...

    I have the 150 4s on a 15' Z7 & I like the engine. For some reason tracker puts a 24p prop on the XS 150 but a 23p on the 4s. Friend of mine told me the 4s has a little bit less low end torque than...
  18. Trying to figure out what this is that sits behind my prop

    http://www.bbcboards.net/attachment.php?attachmentid=222804&stc=1

    This gasket gasket sits between the housing of the lower unit & my 23p tempest on a 2016 Mercury 150 hp 4 stroke. I'm looking into...
  19. I'm spinning right at 6k on rpms running 60 mph....

    I'm spinning right at 6k on rpms running 60 mph. No jack plate. Also has a "gasket of some sort" that rubs with my 24p razor. Enclosed is a pic. Took it off & it turns fine by hand, just want to make...
  20. Prop question z7 23 tempest or 24 razor on 150 hp merc 4s

    Asked in the prop section with not much response. Main question is:
    2015 Z7 - Mercury 150 hp 4 stroke came with 23p tempest. Wanting to know if I can squeeze a couple more mph out of a 24p razor...
  21. Also would like to ask whether to unplug holes or...

    Also would like to ask whether to unplug holes or not?
  22. Nitro Z7 150 merc 4s -23p tempest vs 24p razor

    So last yr I blew my engine on the old boat that had mark croxton's 24p razor. Saved my prop & now I'm running a Z7 with a 23p tempest. No JP on the boat & im running 60 mph gps top speed. Usually...
  23. Have heard that same from others, just wasn't...

    Have heard that same from others, just wasn't sure if anyone had run 36v systems on a Z7. Thanks for the input guys!!
  24. Z7 trolling motors - what lb thrust & shaft length?

    My Z 7 came with the maxxum 70 lb 42" thrust & I'm not real happy with it. looking to upgrade & would like opinions on what most are running & think is ideal. looking to go minimum of 80lb but...
  25. Replies
    4
    Views
    425

    this was in another thread regarding the fenders...

    this was in another thread regarding the fenders on a Z 7. I checked mine & notice a break in the weld on the front bumper step. my fenders rattled terribly going down the road. I had mine...
Results 1 to 25 of 107
Page 1 of 5 1 2 3 4