THX!!
Type: Posts; User: Rangman
THX!!
Hey all,
Anyone have link for where to get service manual on line for VF200 SHO 2020?
THX!!
hey 101....did you ever try other props on this setup? I have 2018 ZX200 with 2020 SHO, same prop as you. Its good but wondering if a different prop might yield bit more top end without killing...
Had same touch issue with my solix 10 G2. Sometimes would work for a while after shutdown the on but not always....always stopped working touch sometime through the day. Thought I was going to have...
were you able to get this figured out? I also have solix and 2020 vf200 that I am thinking of hooking up.
Not whole lake blue Wayne. I just have 3 small sections that are blue only without contour lines and depths. (3 areas that happen to be mid lake humps with each area maybe half size of a football...
Hey all,
Unit is up to date with latest software and I am not sure if my issue occurred just since latest update or I just can't figure out how to fix this....
On some mid lake humps (3 of them in...
Thanks OK! Did you ever try other props on it prior to flash?
new to me skeeter and 4.2 sho. REALLY liking this unit. 1st skeeter for me...coming from rang / 2 stroke Merc.
Right now running a 23 T2 with ptp at 3 1/4. (manual JP)
Runs up to 6000 -~ 6100 @ 67...
Hey guys,
Trying figure out what series controls will be replacement for originals.
The controls are getting worn to the point that in cold weather down near freezing they will get very stiff to...
not a plumber but possibly tank / bladder issue as it seems you have no capacity as if tank was not filling and you are basically running off the small amount of water within the lines only. If...
[QUOTE=JOE54;11983154]:thumb up2: looks real weedy , good for fishes though[/QUOTE
VERY good for fish! THX Joe
Got a chance to put boat into the lake tonight.
Idle and getting ~ 6 PSI....Idling out canal to lake and telltale good once stats open....accelerate and get pressure drop / poppet opening as...
UPDATE: Pulled stats and checked them....opening at just over 140 and no obvious debris in either.....replaced as general maintenance anyway.
Did leak down test....all cylinders between 1.5 and ~...
This is within range that I am experiencing issues...TY for the input and I hope to have all necessary parts and tools by next week and stats along with poppet assembly will be my first checks.
Could or would this affect idle psi being high if it were partially blocked from this gasket or just high rpm flow affected?
Mine also has to be in recirculate to prevent water coming into livewells. Always get water in when in "empty"
does it go into reverse ok? if it does then redo proceedure to adjust shift cable to verify not just an adjustment issue....hopefully this is all it is!
had grey liner issues few years ago on my 2000 175HP EFI. Replaced fuel line, took apart float bowl and found pieces had made it into there also. Cleaned everything well, put it back together (with...
Gauge confirmed as good previously. Why does factory gasket require trimming....it has been working as n normal for 18 years as it was??
Thanks for suggestions
Dave
Yep...gauge is good. I just ordered a proper leak down gauge also so that I have all tools I need hopefully to diagnose further. My plan of attack going forward:
1) Pull stats and verify correct...
Hoping so also....Do you know where "poppet by-pass" is located? I know where the actual poppet valve is but as below exert from Mercury service manual states that "possible causes for over...
Thanks Joe. Never seen it this high even with all new pump parts and have probably 10+ hours on it already since replacement.
Good thought on leakdown just to verify. Don't see any...
Hi to all and hoping someone can help... ****Sorry I have posted this in wrong forum....switching to 2.5 Merc forum****
My Ranger with 2000 175 HP Merc EFI (not opti) has idle water pressure at 10...