Search:

Type: Posts; User: blakes52

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. For anyone else with this issue contact...

    For anyone else with this issue contact powerpole. After speaking with them they are replacing the cylinder free of charge via RMA. They did in fact use bennett cylinders at one point.
  2. I hadn't contacted powerpole yet bc the cylinder...

    I hadn't contacted powerpole yet bc the cylinder clearly had bennett on it so I figured powerpole wouldn't be able to help me being it's not their part. That's my next step if I can't find this part
  3. I have a feeling this may have been a very...

    I have a feeling this may have been a very original powerpole or maybe the previous cylinder went out and was replaced with bennett marine version. The boat is a 99 and I just got it a couple years...
  4. Old style cylinder end Cap (bennett marine cylinder)

    I have an old powerpole which uses a bennett marine lifting cylinder as the actuator. It uses 5/16 hard plastic line with brass slip fitting at each end of the cylinder. I noticed a slight drip from...
  5. I found it small little red plug part number...

    I found it small little red plug part number 859732. I would delete this post but I will leave it up in case someone else needs this Info later
  6. mercury 250xs analog water pressure gauge ?

    I just bought this motor and it came with this kit already installed454672 892156a01 but I am missing the barbed fitting. I have found that which is part number 859731 but I need to plug another line...
  7. after doing more research im leaning towards a...

    after doing more research im leaning towards a simrad go5 setup with vesselview link. My question is what is the real difference of a vesselview 502 and a simrad go5 they seem pretty close in price...
  8. Thanks Don. I sent a message over to parts email...

    Thanks Don. I sent a message over to parts email a little bit ago this morning. So based on what you are saying I will be able to keep my current 8 pin and have a separate 10 pin and have full...
  9. it was a system monitor

    it was a system monitor
  10. question with smartcraft rigging of 250xs

    I am in the middle of a repower to a 2008 250xs, using an 8 pin harness with the mercury adapter to convert to 14pin. I currently have analog gauges and am trying to find the best way to replace the...
  11. Found... mods please remove. Thanks

    Found... mods please remove. Thanks
  12. ISO Livorsi, Hardin marine, Gaffrig single engine control WANTED

    Looking for Livorsi/Gaffrig single engine throttle, thanks!
    http://www.westcoastoffshore.ca/Assets/ProductImages/TH11DPLb.jpg
  13. Replies
    12
    Views
    740

    Thanks for the advice rocketmanjp

    Thanks for the advice rocketmanjp
  14. Replies
    12
    Views
    740

    thanks for all the help ran a couple quotes!

    thanks for all the help ran a couple quotes!
  15. Replies
    12
    Views
    740

    Shipping a motor?

    I currently am selling my motor and have someone interested but I will have to ship it. I haven't ever shipped a motor before so I was wondering if anyone could give some advice on companies to use....
  16. Replies
    6
    Views
    599

    Thanks!

    Thanks!
  17. Replies
    6
    Views
    599

    Rec fuel Harris chain of lakes?

    Anyone on the Harris chain of lakes (preferably closer to leesburg) know which gas stations sell rec fuel? About to get a new motor and will be running rec in it. Hoping someone can save me some time...
  18. Replies
    17
    Views
    2,106

    thanks i am replacing the whole steering system...

    thanks i am replacing the whole steering system with uflex so everything will be new! new!
  19. Replies
    17
    Views
    2,106

    364094

    364094
  20. Replies
    17
    Views
    2,106

    Good news! i was able to get it out. threads on...

    Good news! i was able to get it out. threads on the tiller piece are still there and arent stripped. tried to double nut the reverse the bolt out but i couldnt get it free. finally decided to dremel...
  21. Replies
    17
    Views
    2,106

    the lock nut was removed before the bolt snapped

    the lock nut was removed before the bolt snapped
  22. Replies
    17
    Views
    2,106

    thanks for the answers. i had to remove the...

    thanks for the answers. i had to remove the lower cowling cover to work on it the first time. there was a lock nut below but i was able to remove it. i worked on that thing forever... might try to...
  23. Replies
    17
    Views
    2,106

    mariner tiller bolt question

    (engine is a 1999 mariner 135 opti SN:0G805271)i am replacing the steering system on my boat and the bolt that holds the steering arm of the hydraulic cylinder to the tiller was completely seized to...
  24. Replies
    32
    Views
    1,706

    yea the silversteer is 1500psi... (i looked at...

    yea the silversteer is 1500psi... (i looked at that same listing and i think that is a very old cylinder) the uflex site has the uc130 svs kit online but they arent even manufacturing it yet. the...
  25. My service manual says "Quicksilver TC-W3 Premium...

    My service manual says "Quicksilver TC-W3 Premium Plus 2 Cycle Outboard Oil". i know there is DFI oil but since this motor is a 1999 i dont even think dfi oil was a thing when the motor was made. ...
Results 1 to 25 of 70
Page 1 of 3 1 2 3